VSS Wiring 1985 TPI swap into 86 CCC
#1
Member
Thread Starter
Join Date: Sep 2002
Location: Lehigh Valley, PA
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Pontiac Firebird S/E
Engine: LG4 TPI Conversion
Transmission: 700r4
Axle/Gears: 3.42 SLP Posi 10 Bolt
VSS Wiring 1985 TPI swap into 86 CCC
I picked up another 86 Firebird, with the CC carb. I got a tuned port system from a 1985 I believe a Camaro, and I'm knee-deep in the swap.
Here's what I have done so far:
Dropped the tank and installed a v6 EFI sending unit with a 3.8L TTA pump installed.
Installed 90% of the wiring
Lower manifold and fuel rail installed
Serpentine accy system installed
Fabbed fuel lines to work with TPI motor
The wiring was pulled out of all of the looming (NOT by me) and it's been more fun than allowed by law figuring it all out. I'm confused as to where the VSS plug is, and whether or not I need to fab something up somehow. This car has an electric sending unit already... Do I need to run wires for it? Thanks in advance.
Here's what I have done so far:
Dropped the tank and installed a v6 EFI sending unit with a 3.8L TTA pump installed.
Installed 90% of the wiring
Lower manifold and fuel rail installed
Serpentine accy system installed
Fabbed fuel lines to work with TPI motor
The wiring was pulled out of all of the looming (NOT by me) and it's been more fun than allowed by law figuring it all out. I'm confused as to where the VSS plug is, and whether or not I need to fab something up somehow. This car has an electric sending unit already... Do I need to run wires for it? Thanks in advance.
#2
Member
Thread Starter
Join Date: Sep 2002
Location: Lehigh Valley, PA
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Pontiac Firebird S/E
Engine: LG4 TPI Conversion
Transmission: 700r4
Axle/Gears: 3.42 SLP Posi 10 Bolt
I believe i figured it out. It looks like I have to run the VSS plug with the new harness. It looks like it goes into what I assume is a buffer box, which looks like it feeds back to the ECM.
Any other thoughts?
Any other thoughts?
#3
Junior Member
Join Date: Nov 2003
Location: Enterprise, Alabama
Posts: 71
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 Monte Carlo SS
Engine: 5.0 liter High Output w/ TPI
Transmission: built 700R4 Auto
Axle/Gears: 10 bolt 3.73
It should be a brown wire. On my Monte SS, I just did the 86 to 89 TPI swap on her and on what Painless calls the dash harness, there is a brown wire that is for the VSS. Mine was real close to the computer itself. I am not sure if this helps any.
Todd
Todd
#4
Member
Thread Starter
Join Date: Sep 2002
Location: Lehigh Valley, PA
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Pontiac Firebird S/E
Engine: LG4 TPI Conversion
Transmission: 700r4
Axle/Gears: 3.42 SLP Posi 10 Bolt
There is a brown wire inside. The ones I'm referring to are pinkish purple and yellow. I noticed they did not go to the ecm on the 86's ccc harness... looks like they went to a buffer box, to which the brown wire comes out of.
but thanks for the info!
but thanks for the info!
#5
Supreme Member
Join Date: Jul 2003
Location: KY
Posts: 1,236
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87IROC, 740iBMW, 328iBMW, 86GMC
Engine: 5.7, 4.4LV8, 2.8, 6.0
Transmission: Manuals & Auto's
Axle/Gears: 3.27, 3.42
Originally Posted by 86BirdSE
There is a brown wire inside. The ones I'm referring to are pinkish purple and yellow. I noticed they did not go to the ecm on the 86's ccc harness... looks like they went to a buffer box, to which the brown wire comes out of.
but thanks for the info!
but thanks for the info!
Thread
Thread Starter
Forum
Replies
Last Post
Sanjay
Engine/Drivetrain/Suspension Parts for Sale
1
08-12-2015 03:41 PM
1992 Trans Am
Engine/Drivetrain/Suspension Parts for Sale
1
08-08-2015 08:16 PM
1985, 700r4, 86, auto, box, buffer, conversion, firebird, montecarlo, pontiac, swap, tpi, transmission, vss, wiring