Approx. how much to remove rust & repaint?
Approx. how much to remove rust & repaint?
Im just wondering if any of you guys know approximately how much can i expect to pay to get around the wheel wells sanded and repainted?? From what i remember (I should be purchasing the car very soon) that was the only place where i noticed any rust...tho there may be a few other small spots i didn't notice
Supreme Member

Joined: Apr 2001
Posts: 1,049
Likes: 0
From: Garland, TX, USA
Car: 1992 Camaro RS & 1992 Camaro RS
Engine: 3.1 L v6 & 305 (5.0L) v8
Transmission: 4L60 Auto
If you selling the car a local cheap paint shop can probley do it for 600 or so. If you keep your car, just get the whole car panted for a 1250 if you do the prep.
He means only the wheel wells.
It definately won't cost you that much. It is a pretty low profile area anyway, so you could get away with a quickie job yourself. Do it your self and it will cost you around $50-75 for supplies and paint, and a good couple of hours in the garage.
Now it you are considering buying this car make the owner show you the trouble areas. Mainly the floor pans, but door bottoms, fender lips, subframe. Bring a jack and get under there.
What is it?
------------------
Colin Finkle
87 Sport Coupe Camaro, 5.0 L V8
My Car Craft in/out list:
In: Buying my project Camaro and being the first F-body in High School.
Out: While it is being upgraded 6 V6 F-bodies bodies show up!
Out: Looking like a pazie a** follower.
In: Being the only panzie a** with an 8 under the hood!!!
It definately won't cost you that much. It is a pretty low profile area anyway, so you could get away with a quickie job yourself. Do it your self and it will cost you around $50-75 for supplies and paint, and a good couple of hours in the garage.
Now it you are considering buying this car make the owner show you the trouble areas. Mainly the floor pans, but door bottoms, fender lips, subframe. Bring a jack and get under there.
What is it?
------------------
Colin Finkle
87 Sport Coupe Camaro, 5.0 L V8
My Car Craft in/out list:
In: Buying my project Camaro and being the first F-body in High School.
Out: While it is being upgraded 6 V6 F-bodies bodies show up!
Out: Looking like a pazie a** follower.
In: Being the only panzie a** with an 8 under the hood!!!
yeah, i'll make sure to ask him if there is any other rust or other problems - and as a matter of fact i just may be getting it either today or tomorrow (trying to get my bro to spot me half the money until I sell my Avenger). It's a 1990 Camaro RS, new 350 bored .030 over, rebuilt 700 R4 trans, 2000 stall torque converter, stage 2 shift kit and only 3500 OBO
Joined: Jan 2001
Posts: 8,030
Likes: 1
Car: 1989 IROC-Z
Engine: 383 stroker
Transmission: 700R4 3500 stall, TransGo shift kit
Axle/Gears: Moser 9", 4.11:1
I fixed my own rust around the wheel wells along the fender. I just sanded it down to the metal, masked everything off and applied a few coats of spray primer. Wet sanded the primer smooth, then used a can of Duplicolor auto spray and did 2-3 coats of that, wetsanding between each coat. Came out looking MUCH better, almost perfect. And its a hell of a lot cheaper than getting it done. Good luck.
------------------
1992 Camaro RS For sale! Email me for info!
5.0L TBI
K&N Airfilter and ready to take on the world!
My 1992 RS
Rate my car!
Love the country or leave the country.
------------------
1992 Camaro RS For sale! Email me for info!
5.0L TBI
K&N Airfilter and ready to take on the world!

My 1992 RS
Rate my car!
Love the country or leave the country.
Thread
Thread Starter
Forum
Replies
Last Post
IROCZDAVE (88-L98)
Engine/Drivetrain/Suspension Parts for Sale
0
Sep 2, 2015 08:43 AM
Night rider327
Engine/Drivetrain/Suspension Parts for Sale
0
Sep 2, 2015 04:17 AM





