first post/body parts
Thread Starter
Senior Member
iTrader: (2)
Joined: Jun 2002
Posts: 842
Likes: 1
From: Bergen County, NJ
Car: 1989 IROC-Z
Engine: L98
Transmission: T-56
first post/body parts
hey guys and gals,
can anyone tell me where i can order replacement body parts for my IROC? I need to get new wheelwells (fenderwells). Any input is appreciated.
Thanks,
Matt
can anyone tell me where i can order replacement body parts for my IROC? I need to get new wheelwells (fenderwells). Any input is appreciated.
Thanks,
Matt
Senior Member
Joined: May 2002
Posts: 783
Likes: 0
From: Tucson AZ where the 3k ft of elevation kills your time
Car: 89 camaro rs
Engine: 383 .06 over
Transmission: th350
Axle/Gears: 3.73 10 bolt
junkyards you can find just about anything in a junkyard and if not you can also post a thread in the classifieds on this web site, I needed a steering calumn so I posted a thread on the classifieds and so many people replyed that i did not know wich one to buy good deals too and some honst people. Just post a thead and give it a day or two and you sould get several emails just make sure that you and your email adress so they can write you with there deals
.
. Member

Joined: Feb 2001
Posts: 428
Likes: 0
From: NJ
Car: 88 GTA
Engine: 305
Transmission: Auto
Axle/Gears: 3.23
hey NJITIROC welcome to the boards.
i have both plastic inner fender thingy's from an 89 gta, should work for you
you can come and pick them up 10 bux a pop or so
i have both plastic inner fender thingy's from an 89 gta, should work for you
you can come and pick them up 10 bux a pop or so
Thread Starter
Senior Member
iTrader: (2)
Joined: Jun 2002
Posts: 842
Likes: 1
From: Bergen County, NJ
Car: 1989 IROC-Z
Engine: L98
Transmission: T-56
Thanks you guys.
I need the actual steel wheel wells. They are rusted out. So I want to stay away from a junkyard because those cars probably have the same thing. I need a company that sells new steel replacement ones. Any ideas?
Thanks,
Matt
P.S. Thanks for the welcome.
I need the actual steel wheel wells. They are rusted out. So I want to stay away from a junkyard because those cars probably have the same thing. I need a company that sells new steel replacement ones. Any ideas?
Thanks,
Matt
P.S. Thanks for the welcome.
I had the same problem... I just went to the junkyard and got em, there was nothing wrong with them. I dont think they make replacements... Its not the easiest job either.. but it turned out nice..
Supreme Member
Joined: Mar 2000
Posts: 13,414
Likes: 6
From: Central NJ, USA
Car: 1986 Firebird
Engine: 2.8 V6
Transmission: 700R4
Front or rear? Yep, go to the junkyards... see my message about "quarter panel" a bit below, about rust...
And at junkyards, usually they'll let you see the car that you're getting the panels from! If they don't, then go somewhere else!
And at junkyards, usually they'll let you see the car that you're getting the panels from! If they don't, then go somewhere else! Thread Starter
Senior Member
iTrader: (2)
Joined: Jun 2002
Posts: 842
Likes: 1
From: Bergen County, NJ
Car: 1989 IROC-Z
Engine: L98
Transmission: T-56
thanks dudes,
i NEED the rears, i was maybe gonna look into the fronts as well. ill check out some junkyards. thanks for the input.
i NEED the rears, i was maybe gonna look into the fronts as well. ill check out some junkyards. thanks for the input.
Thread
Thread Starter
Forum
Replies
Last Post
LT1Formula
Engine/Drivetrain/Suspension Parts for Sale
20
Nov 14, 2015 12:02 AM
Thomas
Interior Parts for Sale
12
Oct 3, 2015 05:34 PM




