DFI and ECM Discuss all aspects of DFI (Digital Fuel Injection), ECMs (Electronic Control Module), scanners, and diagnostic equipment. Fine tune your Third Gen computer system for top performance.

Wanting forum member to help with ELB system

Thread Tools
 
Search this Thread
 
Old 06-29-2018, 12:34 PM
  #1  
Junior Member
Thread Starter
 
83 Gman's Avatar
 
Join Date: Sep 2012
Location: Ronkonkoma NY
Posts: 66
Likes: 0
Received 0 Likes on 0 Posts
Wanting forum member to help with ELB system

Hi
I've asked for help/info before on the ELB but I'm sorry I just don't get it.
Looking for someone I can stay in contact with to discuss what I'm missing on tuning this system for my application.
I understand I can change parts of the fuel table without doing a VE learn, which would more than likely correct lean areas of the table.
Thanks
Old 07-14-2018, 09:24 AM
  #2  
Junior Member
Thread Starter
 
83 Gman's Avatar
 
Join Date: Sep 2012
Location: Ronkonkoma NY
Posts: 66
Likes: 0
Received 0 Likes on 0 Posts
Re: Wanting forum member to help with ELB system

Bump
Old 07-21-2018, 12:33 PM
  #3  
Junior Member
Thread Starter
 
83 Gman's Avatar
 
Join Date: Sep 2012
Location: Ronkonkoma NY
Posts: 66
Likes: 0
Received 0 Likes on 0 Posts
Re: Wanting forum member to help with ELB system

I guess I'm beating a dead horse here. Thought I would get a member with knowledge of this system to reply.
Old 07-22-2018, 08:19 PM
  #4  
Member

 
Larry's Avatar
 
Join Date: Sep 1999
Location: San Antonio, Tx
Posts: 199
Received 7 Likes on 7 Posts
Car: 86 Corvette
Re: Wanting forum member to help with ELB system

I just sent you an email.
Old 05-10-2019, 01:58 PM
  #5  
Junior Member
Thread Starter
 
83 Gman's Avatar
 
Join Date: Sep 2012
Location: Ronkonkoma NY
Posts: 66
Likes: 0
Received 0 Likes on 0 Posts
Re: Wanting forum member to help with ELB system

Starting this question up again.
Larry from Texas is/was willing to help, but I'm not good at all knowing how to send info to him via the internet.
I have had this system for quite sometime and can't get a grip on what to do.
Need a person that's close to me that can correct my mistakes and educate me also.
I'm very willing to pay for their time to do so.
I can only fool with this system in warm temperatures.
The car is stored in a rental unit that is non-heated.
That's why I bring this subject up when it gets nice out.
Thanks
Old 05-10-2019, 06:19 PM
  #6  
Supreme Member
iTrader: (1)
 
GeneralDisorder's Avatar
 
Join Date: Mar 2017
Location: Portland, OR
Posts: 4,255
Received 422 Likes on 323 Posts
Car: 86 Imponte Ruiner 450GT, 91 Formula
Engine: 350 Vortec, FIRST TPI, 325 RWHP
Transmission: 700R4 3000 stall.
Axle/Gears: 9 Bolt Torsen 3.70
Re: Wanting forum member to help with ELB system

Would love to help you but I'm in Oregon. Free bump though.

GD
Old 05-19-2019, 08:54 AM
  #7  
Junior Member
Thread Starter
 
83 Gman's Avatar
 
Join Date: Sep 2012
Location: Ronkonkoma NY
Posts: 66
Likes: 0
Received 0 Likes on 0 Posts
Re: Wanting forum member to help with ELB system

Still looking for help. Onlineline or otherwise.
Thanks
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
83 Gman
DIY PROM
8
12-11-2017 03:39 PM
DanZ51
DFI and ECM
3
10-06-2014 11:14 PM
Jim85IROC
Problems / Help / Suggestions / Comments
1
04-23-2010 11:44 AM
WS - 666
Auto Detailing and Appearance
13
10-06-2001 01:39 PM



Quick Reply: Wanting forum member to help with ELB system



All times are GMT -5. The time now is 07:28 PM.