Here are some pics of my kit out of the car...along with the exhaust I made.... This kit is suitable for all smallblock chevies and will support approx. 650 flywheel horsepower. If someone with a 305 is interested I have EVERYTHING....from larger fuel injectors and a chip burnt for boost with larger injectors and a holley adjustable FPR to go with it

out of the car







in the car



I am only selling this because I decided to go to a Twin Turbo setup on the 383 that I am building now with pwergoals to start at 600rwhp. All pictured but the MAF sensor and the O2 sensor are included. Parts included are

BBSdesigns single Race turbo header

A T-61 turbo with 2,000 miles on new bearings and balance.

A turbontetics wastegate with a 5-7psi spring and a 9-13psi spring

All hot piping, aka. turbo header, drivers side header, 2.5" crossover pipe, 3" down pipe, and the custom 3" exhaust w/cutout I made to connect the downpipe to any catback system on a 82-92 Fbody. Also included are all the Band clamps and V-band clamps needed.

charge pipes w/reinforced silicone couplers- from the dischage of the turbo to the throttle body of a TPI. Also comes with a pipe for speed density setups.

A Blitz DD supersound blow off valve.

New copper exhaust gaskets.

Also, available to the purchaser. A custom chip burn't for boost on a 305 TPI, 24# injectors, Holley adjustable Fuel Pressure regulator and a Snow Performance Alcohol injection kit . This would be everything needed to turbo a 305 TPI except fo oil feed and drain lines...Which a local company to me sells an oil kit for $59.95.

If buyer is in a 50 mile radius from Troy, Ohio I would be more than happy to help with the install.

This is listed on Ebay, but for TGO members and another local Fbody board I am including my Snow performance Alcohol injection kit and adjustable FPR with the sale
If you dont need the chip I'd rather donate it to someone on the boards turboing a 305TPI

$1600 plus shipping...which I estimate being around $150 due to weight and size.


If I left anything else out I will update it....


I also have A practically brand new Flowmaster American Thunder full 3" exhaust system..I always ran thru my cutout....I want $200 for it but I would prefer not to ship it due to the expense.

 

Nice car. Did you get the parts installed you purchased from me?
Jeff

 

Sure did....everything is perfect.....now its all changing LOL

 

Any chance you want to trade for a Moser 12-bolt with 3.73s in it for your turbo setup + some cash? Setup for a 4th gen, so you'd need to go with new wheels (unless you want the tires to stick out in the back about an inch and a half from where they are now).

 

I just put a rearend in my car....I'da been down with that too...I am however looking for a tranny to hold lotsa power....

 

Did you get my PM???

 

Sorry I didnt post this sooner...Sale pending

 

will this fit on a 305 tbi

 

with a pressure bonnet and some mods to the charge pipe yes it would work. At the moment the sale is pending...

 

do you have any pics of just the turbo manifold, im curious to see how it was made, i might be putting this on my 305 out of my camaro into an s-10, so i was wondering how much you wanted for the injectors and chip etc, thanks, oh an my email is ncmarine6116@yahoo.com thanks

 

I wouldnt get too excited.....I take it to the guy friday...it is pretty much sold we just have to make the exchange friday at noon

 

awww, well can you at least snap some pics of the turbo header? was it from a kit or did you have them made/make them yourself?

 

Just search BBSdesigns...I think there is a pick somewhere on this site....its the single race header...

 

Can't wait to bolt this baby up and blow the motor to hell haha

 

ahh ok i wasnt sure if it was an over the counter kinda thing or custom, bbs is good stuff...too bad they closed because of cheap knock-offs