nah,they test and tune on fridays.its cool.........i'll have the parts till someone wants them........everything i've sold comes in spirts.........lol

 

anyone have a b&m or pro 5.0 or hurst shifter for a t5 they wanna trade my holley intank pump or pp2 programmer for?

 

How tough is it gonna be to strip all that paint off.I`m going for the stock look and like the natural or polished finish on intake parts

 

it shouldn't be that bad,probably a lil paint remover.or you can bead blast it

 

Just supporting my fellow mississippian! I'm in the process of selling a lot of parts too. Basically everything in my sig except the car. I'm in Hattiesburg, MS. Going LS1!

 

pics of cai, injectors,fuel pump,throttlebody

 

continued

 

injectors and pump. and i will throw in the throttle cable with purchase of throttlebody

 

plenums are sold.

i still have the accel ijectors,holley fuel pump,both sets of stock runners(one set dented),both lower intakes,bbk throttlebody,and fuel rail w/bbk afpr.also stock lt1 injectors.and i still have the slp cai

 

Have any pics of the runners yet?

 

How much for the Fuel Rails without injectors or the Regulator?

 

i will bring them home today and post pics for you.i've been trying to clean them.i haven't forgot about you
----------
50 shipped and that will include the lines that go behind the alternator on a serp system

 

pics of runners.i tried to clean them a little.all 4 of them 50 plus shipping.
one runner has ninth injector provision

 

Thanks for the pics, I really appreciate it. Give me a little time, I need to decide if it's going to be easier to fix yours or mine.... Thanks again!

 

i understand


i really think the one set would look good polished.

 

Is the dizzy still available?

 

yes
100 shipped

 

pic of dizzy

 

bump.......................i also have a pp2 programmer for sale in mis parts........all you need is tuning software.......

 

https://www.thirdgen.org/forums/misc...ammer-2-a.html

 

comeon guys..........i'll take 125 forn the 255lph holley intank pump and 200 for the acell injectors plus shipping.i know someone is interested

 

I would love to by some of this but I`m unable at the moment.What #/hr are the stock LT1 injectors.I know someone who may need some.Is that holley fuel pump for F.I. I think it is,I could use it and the bbk t/b but it may be a week or two for I can get the cash up.In the middle of trying to buy a house so stuffs tight,but I`m deffinatly interested.The mildly ported base for 86 older alluminum heads,thats for 113 casting right?What do you mean by mildly ported,cause I have those heads and could use it as well.

 

i could be wrong ,but i believe they are 24#.i also have a new set of 32# accel injectors.the pump is for fuel injection and is an intank pump.the porting on the intake is on the gasket to head side,they were opened up a little to gasket match my 200 cc sportsman II's.they should be fine for stock heads be it aluminum or cast iron.i ended up using smaller gaskets on the intake than what world products suggested.

 

this stuff has got to go..........i need the money to replace my rear end in my car.gotta get away from the 10 bolt..lol broke another axle.

 

still for sale

stock lt1 injectors 8 run for 6000 miles 200 shipped paid 65 a peice new
accel 32# injectors 8 used 10 minutes 200 plus shipping
holley intank 255lph pump nib 125 plus shipping
slp cai with k&n air filter used for 2000 miles 200 plus shipping
stock fuel rails 50 plus shipping
stock distributor with coil bracket and jumper harness to coil 100 plus shipping
86 down tpi baseplate 75 shipped
87 up tpi baseplate 75 shipped
stock runners 2 sets for one price 65 shipped both sets
one 1227730 ecm no prom used 50 plus shipping SOLD!!!!
bbk 58 mm throttlebody with iac and tps and accelerator cable 250 plus shipping

 

ttt.



i know you guys want some of this stuff

 

you still have the ecm? i'll take the ecm if you still have it?

 

pm sent

 

parts list has been updated

 

bump. i need these parts gone

 

ttt

 

wouldnt happen to have a throttle cable, or cruise control cable for tpi would ya? PM me if you do please.

 

yep,i should have both.the throttle cable i was thinking about letting go with the t/b though.but i can sell it seperatly

 

sunday bump........injectors,throttlebody,stock runners,holley pump ,and slp cai are all still available

 

time to bump this again...............comeon guys stuff needs to go.....i really don't wanna ebay any of this

 

anyone?

 

still have parts for sale............anyone.....i need to get rid of this stuff

 

guys i really don't want to put this stuff on ebay.i would rather ya'll get them than someone else.

 

so which price is it???

 

50 plus shipping

 

ok what is shipping to 94533???

 

through fed ex around 20 to 25 shipped........but thats just from what i got off their website.i usually ship usps,but they take a week or two to deliver.ups is probably gonna be about the same.

so i guess i should have said 75 shipped for the intake.

 

do you have a pic of it?

 

let me check

 

what do you have for heads taht would fit an 87 350 tpi?

 

here are a few pics

 

and a couple more

 

i have a set of heads off a tbi 350 from a truck that have been machined for screw in studs and guide plates.........they need springs.i may have the springs off of them,but i would have the heads reworked.and yes they will work with tpi......i used them for a couple of years before i had the machine work done.i just replaced the heads with some world products sportsman 2's.

 

well that intake is what i need you take paypal??
----------
oh is there anyway to get a pic from above???

 

yes i take paypal.xtremez28@aol.com
are you talking about the heads?i am going over to my parents to pic up another tranny for parts.i can get the heads also and take a pic of them and post later.