[NJ] 2 series 26 spline open carrier wanted
08-31-2017, 02:00 PM
#1
Junior Member
Thread Starter
iTrader: (3)
Join Date: Jul 2011
Location: Ukraine
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 F-bird
Engine: 350 Vortec
Transmission: Manual
Axle/Gears: 3.42
2 series 26 spline open carrier wanted
Looking for 2 series open carrier (2.73/3.08 gears) with 26 splines (1982-89) in decent condition.
I know, they're not so desirable as 3 series, so, please, offer some good prices.
Shipping to 07936 NJ
I'm going to try 3.08 gears instead of 3.42 with my v6 T5 transmission behind mild 350.
I know, they're not so desirable as 3 series, so, please, offer some good prices.
Shipping to 07936 NJ
I'm going to try 3.08 gears instead of 3.42 with my v6 T5 transmission behind mild 350.
08-31-2017, 07:03 PM
#2
Supreme Member
iTrader: (1)
Join Date: Feb 2017
Location: Meriden, CT 06450
Posts: 4,030
Received 511 Likes
on
428 Posts
Car: 84 TA orig. 305 LG4 "H" E4ME
Engine: 334 SBC - stroked 305 M4ME Q-Jet
Transmission: upgraded 700R4 3200 stall
Axle/Gears: 10bolt 4.10 Posi w Lakewood TA Bars
Re: 2 series 26 spline open carrier wanted
I will check my original. 100K miles when pulled and was babied.
09-01-2017, 06:00 PM
#3
Supreme Member
iTrader: (1)
Join Date: Feb 2017
Location: Meriden, CT 06450
Posts: 4,030
Received 511 Likes
on
428 Posts
Car: 84 TA orig. 305 LG4 "H" E4ME
Engine: 334 SBC - stroked 305 M4ME Q-Jet
Transmission: upgraded 700R4 3200 stall
Axle/Gears: 10bolt 4.10 Posi w Lakewood TA Bars
Re: 2 series 26 spline open carrier wanted
I checked. It's a 7.5/7.625" from my 84 TA 10 bolt 26 spline gov-lock.
42 & 13 teeth = 3.23 gear ratio. Bearings and races still on it with no rust.
I guess this is not what you are looking for.
42 & 13 teeth = 3.23 gear ratio. Bearings and races still on it with no rust.
I guess this is not what you are looking for.
09-02-2017, 02:17 AM
#4
Junior Member
Thread Starter
iTrader: (3)
Join Date: Jul 2011
Location: Ukraine
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 F-bird
Engine: 350 Vortec
Transmission: Manual
Axle/Gears: 3.42
Re: 2 series 26 spline open carrier wanted
I decided to go with my 3-series carrier and thin 3.08 gear.
Anyway, thanks for your time!
Anyway, thanks for your time!
10-09-2017, 07:32 PM
#5
Supreme Member
iTrader: (1)
Join Date: Feb 2017
Location: Meriden, CT 06450
Posts: 4,030
Received 511 Likes
on
428 Posts
Car: 84 TA orig. 305 LG4 "H" E4ME
Engine: 334 SBC - stroked 305 M4ME Q-Jet
Transmission: upgraded 700R4 3200 stall
Axle/Gears: 10bolt 4.10 Posi w Lakewood TA Bars
Re: 2 series 26 spline open carrier wanted
It's probably too late, and I doubt if this will help, but I found this: http://www.ebay.com/itm/NOS-1982-199...xYfkBW&vxp=mtr