Chassis Dyno in West Michigan??
Thread Starter
Member
Joined: Jan 2005
Posts: 391
Likes: 0
From: Grand Rapids, Mi
Car: 1991 Z28
Engine: 357
Transmission: T-56 waiting to go in!
Axle/Gears: 3.73:1
Chassis Dyno in West Michigan??
Anyone know fo any shops in the west michigan/ Grand Rapida area that have a chassis dyno that they will let you use?
Joined: Sep 1999
Posts: 1,405
Likes: 8
From: Grand Rapids, MI
Car: 1985 IROC-Z
Engine: Magnacharged LS1
Transmission: T56
Axle/Gears: Ford 9" 4:11's
Zack, there is a place in Nunica...can't remember the name off the top of my head though
TGO Supporter
Joined: Jul 2003
Posts: 4,803
Likes: 2
From: Grand Rapids, MI
Car: Z28
Engine: Sb2.2 406
Transmission: Jerico 4 speed
Axle/Gears: Ford 9" 3.60
Baker has a chassis dyno, yes. I know a few people who have been there. Not sure how much or whatnot, though.
*edit* Just looked it up. We should get a group or something this summer out there.
*edit* Just looked it up. We should get a group or something this summer out there.
Single pull = $50 (a couple “runs” to measure torque/horsepower)
By the hour = $125/hr for first hour; $75/hr thereafter (for testing and tuning)
Discount rates for car clubs or other groups of 8 or more.
By the hour = $125/hr for first hour; $75/hr thereafter (for testing and tuning)
Discount rates for car clubs or other groups of 8 or more.
Last edited by Stekman; Jan 10, 2005 at 10:19 PM.
Thread Starter
Member
Joined: Jan 2005
Posts: 391
Likes: 0
From: Grand Rapids, Mi
Car: 1991 Z28
Engine: 357
Transmission: T-56 waiting to go in!
Axle/Gears: 3.73:1
well i know of at least three guys who will go so lets find 5 more and do it...i need to know where im at hp wise
TGO Supporter
iTrader: (4)
Joined: Oct 2004
Posts: 300
Likes: 0
From: Rockford, MI
Car: 1983 Pontiac Trans AM
Engine: 355 chevy
Transmission: 700R4 Built
Axle/Gears: Built 10 bolt 3.73 gears
I will do it. I'm putting a 355 in my TA and i'm lookin to make about 400hp. It would be cool to get it on the dyno if I can get it finished.
**now that i think about it my brother would too. Hes got an 84 regal we built for street/strip and an 82 ta he probably wouldn't mind bringing over here.
J.
**now that i think about it my brother would too. Hes got an 84 regal we built for street/strip and an 82 ta he probably wouldn't mind bringing over here.
J.
Last edited by eXesiv|83ta; Jan 11, 2005 at 07:15 PM.
Trending Topics
TGO Supporter
Joined: Jul 2003
Posts: 4,803
Likes: 2
From: Grand Rapids, MI
Car: Z28
Engine: Sb2.2 406
Transmission: Jerico 4 speed
Axle/Gears: Ford 9" 3.60
I think I might have a friend who may be interested as well.
I just sent them an E-mail regarding the pricing for a few number runs for a group of about 8-15. So we'll see what we're looking at.
I just sent them an E-mail regarding the pricing for a few number runs for a group of about 8-15. So we'll see what we're looking at.
Thread Starter
Member
Joined: Jan 2005
Posts: 391
Likes: 0
From: Grand Rapids, Mi
Car: 1991 Z28
Engine: 357
Transmission: T-56 waiting to go in!
Axle/Gears: 3.73:1
thats fine though because im just looking to see where my car is at right now, kinda get a baseline number before i add new heads and then after.
TGO Supporter
Joined: Jul 2003
Posts: 4,803
Likes: 2
From: Grand Rapids, MI
Car: Z28
Engine: Sb2.2 406
Transmission: Jerico 4 speed
Axle/Gears: Ford 9" 3.60
Here is what they say:
Mike,
Thanks for your interest in the Chassis Dyno at Baker Engineering. We
typically run events like this on Saturday mornings (8 am to 11) and the
group price is $40 per car for 10 or more ($400 minimum so if there are
fewer cars, each pays a little more). And yes, these are usually "single
pulls" which means that each car gets to make two or three runs
back-to-back. If someone wants to do some tuning, and put the car back on
the dyno, that would be considered two separate sessions, and that person
would pay $80. Each person gets a printout of the data collected. March is
good month to schedule such an event. Give us a call if you have any other
questions.
Sue J.
Thanks for your interest in the Chassis Dyno at Baker Engineering. We
typically run events like this on Saturday mornings (8 am to 11) and the
group price is $40 per car for 10 or more ($400 minimum so if there are
fewer cars, each pays a little more). And yes, these are usually "single
pulls" which means that each car gets to make two or three runs
back-to-back. If someone wants to do some tuning, and put the car back on
the dyno, that would be considered two separate sessions, and that person
would pay $80. Each person gets a printout of the data collected. March is
good month to schedule such an event. Give us a call if you have any other
questions.
Sue J.
Thread Starter
Member
Joined: Jan 2005
Posts: 391
Likes: 0
From: Grand Rapids, Mi
Car: 1991 Z28
Engine: 357
Transmission: T-56 waiting to go in!
Axle/Gears: 3.73:1
well what are we waiting for...anyone who just wants to get some baselien numbers lets get over there in march
Thread Starter
Member
Joined: Jan 2005
Posts: 391
Likes: 0
From: Grand Rapids, Mi
Car: 1991 Z28
Engine: 357
Transmission: T-56 waiting to go in!
Axle/Gears: 3.73:1
i knew you guys would be in (james and matt) Lets seriously get this rollin, we can see who the big dog is haha. My money is prolly on james but i guess we'll see.
TGO Supporter
Joined: Jul 2003
Posts: 4,803
Likes: 2
From: Grand Rapids, MI
Car: Z28
Engine: Sb2.2 406
Transmission: Jerico 4 speed
Axle/Gears: Ford 9" 3.60
Not that far in the south east corner. I'm maybe 15 minutes highway time from the Cascade area. However, my Camaro is stored about 15 minutes east of Studio 28, if you know where that is.
Thread
Thread Starter
Forum
Replies
Last Post
darwinprice
Organized Drag Racing and Autocross
17
Oct 11, 2015 11:51 PM
LT1Formula
Engine/Drivetrain/Suspension Parts for Sale
7
Oct 8, 2015 08:34 PM
