help me reinforce my rear Hi all! i would like some cheap insurance for my rear end. I know i can weld the axle tubes, but what else can i do short of an axle swap to beef up a 10 bolt? i'm looking for cheap or free here. thanks. |
Re: help me reinforce my rear other than that, upgrade to 28 spline axles. the weak link is still the ring and pinion, its only a matter of time before something happens. |
Re: help me reinforce my rear A T/A PErformance aluminum cover can help. They are not cheap or free, but they do strengthen the housing and bearing caps. 28 spline axles and an Eaton piosi will also help, but also not cheap or free. |
Re: help me reinforce my rear Yea, nothing is cheap or free, but the aluminum girdle (the cover) is the main point. A better posi, aftermarket 28 spline axles... those help a lot. |
Re: help me reinforce my rear thanks guys for the input. i have the posi unit and i guess ill just weld my axle tubes and get the girdle. how much power you think that can take? |
Re: help me reinforce my rear The only things that I did to my diff was weld the axle tubes and used a TA girdle. Best 60ft was 1.52 Best et was 11.00 @ 125mph. That was a stock diff otherwise(gm 10bolt, 7.625) with a 700r4 BTW, I blew the diff on the last pass on the last race of the year. 165hp shot of nitrous off the line was just too much. I dyno'd my car and it was 377hp to the wheels(that was na) http://img.photobucket.com/albums/v6...A/PA040052.jpg |
Re: help me reinforce my rear Was that a Governor Lock? |
Re: help me reinforce my rear It was a limited slip(not sure on the correct terminology) |
Re: help me reinforce my rear well my car only dynoed at 281 hp to the wheels and 332 torque. i don't have nitrous so i guess i'll be ok. |
Re: help me reinforce my rear |
Re: help me reinforce my rear Yah. It's hard to picture it now that mine has grenaded so bad.!! HAHA |
Re: help me reinforce my rear Those aren't very strong. Just wondering, why do you have 3 studs and 1 bolt in the bearing caps? |
Re: help me reinforce my rear Not sure! I put the TA cover on about 3yrs ago and put in sythetic fluid and haven't look at it since. I was guessing at the time that it wouldn't last long. |
Re: help me reinforce my rear I tried sliding 28 spline axles in a 26 spline rear, after changing the spider gears. No posi involved at that time. Didn't want to undo the caps. Anyway, doesn't work. You hafta change the carrier. If your car has drum brakes, you can just get a later axle. Try a 90-92 V6 automatic car for the 28 spline axles with a 3.42:1, 7.625" setup, then spend $350 for a conversion locker. Or not. Worked well for me. |
Re: help me reinforce my rear
Originally Posted by LB9GTA
(Post 3926095)
The only things that I did to my diff was weld the axle tubes and used a TA girdle. Best 60ft was 1.52 Best et was 11.00 @ 125mph. That was a stock diff otherwise(gm 10bolt, 7.625) with a 700r4 BTW, I blew the diff on the last pass on the last race of the year. 165hp shot of nitrous off the line was just too much. I dyno'd my car and it was 377hp to the wheels(that was na) Not to hyjack the thread but, What did the car run on motor at the 377 RWHP. What did it run with the nitrous? Thanks! |
Re: help me reinforce my rear Check my sig |
All times are GMT -5. The time now is 11:16 PM. |
© 2024 MH Sub I, LLC dba Internet Brands