Third Generation F-Body Message Boards
Share Your Pictures with Our Community. Upload Now
0 2020/07/14 22:12:48
0 2020/07/14 22:12:14
0 2020/07/14 22:12:02
0 2020/07/14 22:11:28
0 2020/07/14 21:08:29
0 2020/07/14 21:08:05
0 2020/07/14 21:07:30
0 2020/07/14 21:06:28
0 2020/07/14 19:36:09
0 2020/07/14 19:23:05
0 2020/07/14 18:49:05
0 2020/07/14 18:31:19
Advertisement
0 2020/07/14 18:30:58
0 2020/07/14 18:30:40
I am planning on getting an adapter to connect the throttle body coolant passage to this radiator heater hose so that I don't need to worry about bleeding.
I am planning on getting an adapter to connect the throttle body coolant passage to this radiator heater hose so that I don't need to worry about bleeding.
0 2020/07/14 18:30:24
For the throttle body coolant passage, I just capped it off for now. If you are doing this, it is important to bleed the air out whenever you refill your coolant.
For the throttle body coolant passage, I just capped it off for now. If you are doing this, it is important to bleed the air out whenever you refill your coolant.
0 2020/07/14 18:30:10
0 2020/07/14 18:29:47
For now just running the facotry truck fusebox underneath the hood. Truck harness is still pretty much uncut.
For now just running the facotry truck fusebox underneath the hood. Truck harness is still pretty much uncut.
0 2020/07/14 18:29:31
Custom throttle cable bracket. Could have used the stock truck one though.
Custom throttle cable bracket. Could have used the stock truck one though.
0 2020/07/14 18:29:17
For the transmission kick down cable I already had the bracket on my factory lsx throttle body, I just had to rotate it 180 degrees.
For the transmission kick down cable I already had the bracket on my factory lsx throttle body, I just had to rotate it 180 degrees.
0 2020/07/14 18:28:53
For the intake I used a silverado intake coupler with the silverado maf. I then used a 4 inch to 3.5 inch adapter to be able to use the tpi intake
For the intake I used a silverado intake coupler with the silverado maf. I then used a 4 inch to 3.5 inch adapter to be able to use the tpi intake
0 2020/07/14 18:28:32
Temporary switch panel until I get parts for my 3d printer. Planning on 3d printing a factoryish looking place for the switches.
Temporary switch panel until I get parts for my 3d printer. Planning on 3d printing a factoryish looking place for the switches.
0 2020/07/14 18:28:05
Fuel pump that I installed into the factory tank
Fuel pump that I installed into the factory tank
0 2020/07/14 18:27:52
The garage that I work out of.
The garage that I work out of.
0 2020/07/14 18:27:37
0 2020/07/14 18:27:17
Better picture of the alternator relocation bracket
Better picture of the alternator relocation bracket
0 2020/07/14 18:26:51
Notched edge off top to clear the Sanden. Elongating both holes. Slow progress.
Notched edge off top to clear the Sanden. Elongating both holes. Slow progress.
0 2020/07/14 18:17:08
0 2020/07/14 17:06:46
0 2020/07/14 17:06:31
0 2020/07/14 16:37:32
0 2020/07/14 16:07:57
0 2020/07/14 16:07:20
Advertisement