Third Generation F-Body Message Boards
0 2020/07/13 22:51:15
0 2020/07/13 22:51:18
0 2020/07/13 22:51:22
0 2020/07/13 22:51:26
0 2020/07/13 22:52:35
0 2020/07/13 22:52:41
0 2020/07/13 22:52:48
0 2020/07/13 22:52:55
0 2020/07/13 22:53:01
0 2020/07/13 22:53:09
0 2020/07/13 22:53:15
0 2020/07/13 22:53:22
0 2020/07/13 22:53:29
0 2020/07/13 22:53:35
Better picture of the alternator relocation bracket
Better picture of the alternator relocation bracket
0 2020/07/14 18:26:51
0 2020/07/14 18:27:17
The garage that I work out of.
The garage that I work out of.
0 2020/07/14 18:27:37
Fuel pump that I installed into the factory tank
Fuel pump that I installed into the factory tank
0 2020/07/14 18:27:52
Temporary switch panel until I get parts for my 3d printer. Planning on 3d printing a factoryish looking place for the switches.
Temporary switch panel until I get parts for my 3d printer. Planning on 3d printing a factoryish looking place for the switches.
0 2020/07/14 18:28:05
For the intake I used a silverado intake coupler with the silverado maf. I then used a 4 inch to 3.5 inch adapter to be able to use the tpi intake
For the intake I used a silverado intake coupler with the silverado maf. I then used a 4 inch to 3.5 inch adapter to be able to use the tpi intake
0 2020/07/14 18:28:32
For the transmission kick down cable I already had the bracket on my factory lsx throttle body, I just had to rotate it 180 degrees.
For the transmission kick down cable I already had the bracket on my factory lsx throttle body, I just had to rotate it 180 degrees.
0 2020/07/14 18:28:53
Custom throttle cable bracket. Could have used the stock truck one though.
Custom throttle cable bracket. Could have used the stock truck one though.
0 2020/07/14 18:29:17
For now just running the facotry truck fusebox underneath the hood. Truck harness is still pretty much uncut.
For now just running the facotry truck fusebox underneath the hood. Truck harness is still pretty much uncut.
0 2020/07/14 18:29:31
0 2020/07/14 18:29:47
For the throttle body coolant passage, I just capped it off for now. If you are doing this, it is important to bleed the air out whenever you refill your coolant.
For the throttle body coolant passage, I just capped it off for now. If you are doing this, it is important to bleed the air out whenever you refill your coolant.
0 2020/07/14 18:30:10
I am planning on getting an adapter to connect the throttle body coolant passage to this radiator heater hose so that I don't need to worry about bleeding.
I am planning on getting an adapter to connect the throttle body coolant passage to this radiator heater hose so that I don't need to worry about bleeding.
0 2020/07/14 18:30:24
0 2020/07/14 18:30:40
0 2020/07/14 18:30:58
0 2020/07/14 18:31:19
0 2020/07/14 19:23:05
0 2020/08/06 20:49:11
0 2020/08/06 20:49:48
0 2020/08/06 20:49:55
0 2020/08/06 21:01:28
0 2020/08/06 21:01:30
0 2020/08/06 21:01:32
0 2020/08/06 21:01:34
0 2020/08/06 21:01:35
0 2020/08/06 21:01:38
0 2020/08/06 21:01:43