Third Generation F-Body Message Boards
0 2025/09/20 13:52:52
0 2025/10/01 02:05:42
0 2025/10/01 02:05:40
This is the spacer used on the H.O. passenger side cast iron exhaust manifold with the later N10 dual cat exhaust system. Using my built in eyeball micrometer this spacer is no where near as thick as the older EFE valve style spacer. The older spacer is about 1 3/16 of an inch thick eyeballing it against a Starrett machinist scale.
This is the spacer used on the H.O. passenger side cast iron exhaust manifold with the later N10 dual cat exhaust system. Using my built in eyeball micrometer this spacer is no where near as thick as the older EFE valve style spacer. The older spacer is about 1 3/16 of an inch thick eyeballing it against a Starrett machinist scale.
0 2025/10/01 02:05:44
0 2025/10/01 02:05:45
Fel Pro claims this replaces GM part number 10136836.
Fel Pro claims this replaces GM part number 10136836.
0 2025/10/01 02:05:47
Rubber Bumper that goes between fuel pump and pulsator. Modern turbine style fuel pumps don't need either of those parts.
Rubber Bumper that goes between fuel pump and pulsator. Modern turbine style fuel pumps don't need either of those parts.
0 2025/10/07 22:57:19
0 2025/10/09 13:05:30
0 2025/10/09 13:06:50
0 2025/10/09 13:07:55
0 2025/10/09 13:10:34
0 2025/10/09 13:11:56
A melonized distributor gear at first will appear like any normal iron gear. But if you look closely, the melonized gear (left) offers a mottled appearance on the collar while a standard iron gear is smooth (right). (Image/Jeff Smith) "I believe that is a MSD Pro Billet distributor on the right. It has a fully machined billet aluminum housing with O-ring sealing grooves machined into the lower part of the housing."
A melonized distributor gear at first will appear like any normal iron gear. But if you look closely, the melonized gear (left) offers a mottled appearance on the collar while a standard iron gear is smooth (right). (Image/Jeff Smith) "I believe that is a MSD Pro Billet distributor on the right. It has a fully machined billet aluminum housing with O-ring sealing grooves machined into the lower part of the housing."
0 2025/10/23 04:48:06
GM Genuine Parts 19432310 Distributor Gear.
GM Genuine Parts 19432310 Distributor Gear.
0 2025/10/23 10:30:38
GM Delco ESC Module 16128261 (ANUC)
GM Delco ESC Module 16128261 (ANUC)
0 2025/10/23 12:59:04
GM Delco Knock Sensor 10456018
GM Delco Knock Sensor 10456018
0 2025/10/23 12:59:06
GM Genuine Parts 19432310 Distributor Gear_
GM Genuine Parts 19432310 Distributor Gear_
0 2025/10/24 01:14:55
GM Genuine Parts 19432310 Distributor Gear. (2)
GM Genuine Parts 19432310 Distributor Gear. (2)
0 2025/10/24 03:43:38
GM Genuine Parts 19432310 Distributor Gear. (1)
GM Genuine Parts 19432310 Distributor Gear. (1)
0 2025/10/24 03:43:39
0 2025/10/30 12:49:54
0 2025/10/30 20:21:19
0 2025/10/30 20:21:49
GM pilot bearing purchased from Summit Racing.
GM pilot bearing purchased from Summit Racing.
0 2025/11/04 04:19:55
0 2025/11/04 04:20:11
This picture shows the big bearing has been removed and I'm about to press in the new, small bearing.
This picture shows the big bearing has been removed and I'm about to press in the new, small bearing.
0 2025/11/04 04:20:27
Here is the small, pilot bearing installed. I ***think*** that it's in the proper position.
Here is the small, pilot bearing installed. I ***think*** that it's in the proper position.
0 2025/11/04 04:20:43
GM pilot bearing purchased from Summit Racing.
GM pilot bearing purchased from Summit Racing.
0 2025/11/04 04:31:45
0 2025/11/04 04:33:23
Here is the small, pilot bearing installed. I ***think*** that it's in the proper position.
Here is the small, pilot bearing installed. I ***think*** that it's in the proper position.
0 2025/11/04 04:33:25
This picture shows the big bearing has been removed and I'm about to press in the new, small bearing.
This picture shows the big bearing has been removed and I'm about to press in the new, small bearing.
0 2025/11/04 04:33:26
0 2025/11/04 04:35:40
0 2025/11/04 04:36:20
0 2025/11/04 04:37:03
0 2025/11/04 04:37:44
Blow the picture up and look at the trillions of "Stars" in my plastic T-tops. They aren't on the outside or inside of the T-top. I think they are between the acrylic plastic and the LexAR™ Coat 100 scratch resistant coating.
Blow the picture up and look at the trillions of "Stars" in my plastic T-tops. They aren't on the outside or inside of the T-top. I think they are between the acrylic plastic and the LexAR™ Coat 100 scratch resistant coating.
0 2025/11/17 21:37:01
You can see the label mentioning these are acrylic plastic. The "Starfield" is orders of magnitude worse in real life.
You can see the label mentioning these are acrylic plastic. The "Starfield" is orders of magnitude worse in real life.
0 2025/11/17 21:37:04
Driver side H.O. cast iron manifold.
Driver side H.O. cast iron manifold.
0 2025/12/09 19:07:15
Passenger side H.O. cast iron manifold. Notice longer studs.
Passenger side H.O. cast iron manifold. Notice longer studs.
0 2025/12/09 19:07:18
Passenger side cast iron H.O. manifold spacer fits to flat machined face of passenger side manifold. No gasket is used. Spacer and manifold have a finely machined surface that seal together.
Passenger side cast iron H.O. manifold spacer fits to flat machined face of passenger side manifold. No gasket is used. Spacer and manifold have a finely machined surface that seal together.
0 2025/12/09 19:07:20
99.999% of the time when you try to buy a set of these H.O. cast iron manifolds the H.O. cast iron spacer is nowhere to be found. The H.O. manifolds are useless without this spacer.
99.999% of the time when you try to buy a set of these H.O. cast iron manifolds the H.O. cast iron spacer is nowhere to be found. The H.O. manifolds are useless without this spacer.
0 2025/12/09 19:07:22