Third Generation F-Body Message Boards
You can see it is darker than the previous (which I re-wrapped later today to match, both sides. It goes better with the carpet color as well as blending with the gold in the sacred bird, IMHO
You can see it is darker than the previous (which I re-wrapped later today to match, both sides. It goes better with the carpet color as well as blending with the gold in the sacred bird, IMHO
0 2021/04/08 16:45:19
Wrapped the other side, seam at the rear ash tray worked good. Didn't have a long enough piece to do the whole shmear.
Wrapped the other side, seam at the rear ash tray worked good. Didn't have a long enough piece to do the whole shmear.
0 2021/04/08 16:48:14
Seam at rear ash tray, barely noticeable. Don't anticipate anyone sitting back there anyhow.
Seam at rear ash tray, barely noticeable. Don't anticipate anyone sitting back there anyhow.
0 2021/04/08 16:51:49
I am liking this!
I am liking this!
0 2021/04/08 17:02:15
0 2021/04/09 08:41:32
0 2021/04/09 08:42:04
So cool
So cool
0 2021/04/09 08:42:45
0 2021/04/09 17:15:30
0 2021/04/09 17:17:16
0 2021/04/09 17:18:20
After
After
0 2021/04/09 17:20:12
After 2600 PSI argh argh argh!!
After 2600 PSI argh argh argh!!
0 2021/04/09 17:21:11
Looking very cozy in the cockpit!!!
Looking very cozy in the cockpit!!!
0 2021/04/09 17:28:19
0 2021/04/09 17:29:57
0 2021/04/09 17:31:30
0 2021/04/09 17:34:46
Looking really cozy in the cockpit
Looking really cozy in the cockpit
0 2021/04/09 17:36:11
Another angle
Another angle
0 2021/04/09 17:39:01
0 2021/04/10 04:23:46
I tried to grab him for a better photo, but he disappeared. Here is what they look like.
I tried to grab him for a better photo, but he disappeared. Here is what they look like.
0 2021/04/10 16:56:12
FYI
FYI
0 2021/04/10 16:57:42
I bought a replacement for this HVAC switch because it looked rusty. Turns out it was just the color of the plastic. Gotcha!
I bought a replacement for this HVAC switch because it looked rusty. Turns out it was just the color of the plastic. Gotcha!
0 2021/04/10 16:59:41
Drilled the hole for my rear hatch release switch. I think it looks pretty OEM. Feels good too.
Drilled the hole for my rear hatch release switch. I think it looks pretty OEM. Feels good too.
0 2021/04/10 17:02:33
0 2021/04/10 17:04:27
0 2021/04/10 17:05:09
I do not remember disconnecting, but it looks important. Anyone know what it is?
I do not remember disconnecting, but it looks important. Anyone know what it is?
0 2021/04/10 17:05:48
Same question with this thing?
Same question with this thing?
0 2021/04/10 17:07:04
0 2021/04/10 17:08:56
0 2021/04/10 17:11:37
0 2021/04/10 17:12:01
Boring window switches from another angle. :)
Boring window switches from another angle. :)
0 2021/04/10 17:13:18
Started on the door cards today
Started on the door cards today
0 2021/04/11 16:47:06
Impressive spike strips to hold the trim piece in
Impressive spike strips to hold the trim piece in
0 2021/04/11 16:48:54
Finally figured out how to remove these pesky nuts after I ripped out the door cardboard.
Finally figured out how to remove these pesky nuts after I ripped out the door cardboard.
0 2021/04/11 16:49:58
Many tears and cracks, will reinforce with some oak strips, remnants from a previous woodworking project.
Many tears and cracks, will reinforce with some oak strips, remnants from a previous woodworking project.
0 2021/04/11 16:52:01
Plan to paint the cardboard with some low viscosity epoxy I had left over from the boat. Hopefully make i a little more weather impervious.
Plan to paint the cardboard with some low viscosity epoxy I had left over from the boat. Hopefully make i a little more weather impervious.
0 2021/04/11 16:54:44
I decided to go with the black vinyl on this panel, left the old fabric with the padding. I think it will better meld with the black dash coming around the corner. I only cemented the edges so the foam was unaffected.
I decided to go with the black vinyl on this panel, left the old fabric with the padding. I think it will better meld with the black dash coming around the corner. I only cemented the edges so the foam was unaffected.
0 2021/04/11 16:56:52
For reference
For reference
0 2021/04/11 17:00:20
0 2021/04/11 17:01:40
0 2021/04/11 17:02:35