Third Generation F-Body Message Boards
What a pain in the butt to install the springs. Ended up removing the control arms and using it in the equation to compress the springs. Reinstalled the control arms with springs not fully seated in the pocket of the cross member. A ratchet strap attached to a coil and to a point on the opposite side of the cross member for the seated correctly.
What a pain in the butt to install the springs. Ended up removing the control arms and using it in the equation to compress the springs. Reinstalled the control arms with springs not fully seated in the pocket of the cross member. A ratchet strap attached to a coil and to a point on the opposite side of the cross member for the seated correctly.
0 2026/04/17 21:15:27
Had the original sway bar powder coated and installed the steering linkage parts.
Had the original sway bar powder coated and installed the steering linkage parts.
0 2026/04/17 21:15:23
Bump stops mounts for the hood painted as well.
Bump stops mounts for the hood painted as well.
0 2026/04/17 21:15:20
Bumper upper mounting bracket painted with sem trim black.
Bumper upper mounting bracket painted with sem trim black.
0 2026/04/17 21:15:18
Hardware for the power steering cooler.
Hardware for the power steering cooler.
0 2026/04/17 21:15:16
Factory power steering cooler cleaned and painted.
Factory power steering cooler cleaned and painted.
0 2026/04/17 21:15:13
New condenser and old radiator installed. I used the expanding foam strip that you can get from HD to seal in between the two.
New condenser and old radiator installed. I used the expanding foam strip that you can get from HD to seal in between the two.
0 2026/04/17 21:15:10
0 2026/04/17 21:05:33
TDS bar, sway bar, and pro forge steering components installed.
TDS bar, sway bar, and pro forge steering components installed.
0 2026/04/17 21:05:30
Hardware for the powering steering cooler also painted.
Hardware for the powering steering cooler also painted.
0 2026/04/17 21:05:27
Factory power steering cooler cleaned up and painted with sem paint.
Factory power steering cooler cleaned up and painted with sem paint.
0 2026/04/17 21:05:23
Parallel condenser with the expanding strip foam from HD installed along with the radiator.
Parallel condenser with the expanding strip foam from HD installed along with the radiator.
0 2026/04/17 21:05:20
0 2025/12/02 21:24:19
0 2025/12/02 21:24:18
0 2025/08/26 05:17:41
Racetronix fuel pump hot wire kit and tank ready to be installed.
Racetronix fuel pump hot wire kit and tank ready to be installed.
0 2025/06/06 23:40:35
New 255lph pump installed into the fuel bucket along with a new 0-90 ohm sender card.
New 255lph pump installed into the fuel bucket along with a new 0-90 ohm sender card.
0 2025/06/06 23:40:32
4th gen fuel tank bulkhead connector that will be replacing the 3rd gen connector for the fuel tank upgrade. I want a fully functional 4th gen setup. Evap system along with the fuel tank pressure sensor to go along with the 0411 ecm.
4th gen fuel tank bulkhead connector that will be replacing the 3rd gen connector for the fuel tank upgrade. I want a fully functional 4th gen setup. Evap system along with the fuel tank pressure sensor to go along with the 0411 ecm.
0 2025/06/06 23:40:30
HVAC box reinstalled on the firewall. I also reloomed the wiring harnesses in the engine bay.
HVAC box reinstalled on the firewall. I also reloomed the wiring harnesses in the engine bay.
0 2025/06/06 23:40:26
0 2025/05/23 20:19:28
0 2024/10/17 22:46:30
0 2024/10/11 22:26:52
0 2024/10/11 22:26:49
0 2024/10/11 22:26:46
0 2024/10/11 22:26:43
0 2024/10/11 22:26:40
0 2024/10/11 22:26:37
Sbc Holley mid mount accessory bracket kit. I like this because of the water pump design. No longer have to remove everything to replace the pump. Just take out the impeller.
Sbc Holley mid mount accessory bracket kit. I like this because of the water pump design. No longer have to remove everything to replace the pump. Just take out the impeller.
0 2024/10/07 19:34:58
Original air upgrade kit
Original air upgrade kit
0 2024/10/07 19:34:56
0 2024/10/03 18:28:12
0 2024/10/03 18:28:09
0 2024/10/03 18:28:05
0 2024/10/03 18:28:02
New 0411 wiring harness for efi connections
New 0411 wiring harness for efi connections
0 2024/10/03 18:27:58
0 2024/10/03 18:27:56
New lines finished
New lines finished
0 2024/10/03 18:27:51
You can see the 3rd gen lines still in the proportioning valve here.
You can see the 3rd gen lines still in the proportioning valve here.
0 2024/10/03 18:27:46
Pot-15 then rattle can
Pot-15 then rattle can
0 2024/09/26 20:08:19
Everything welded in and undercoated. The weld on the plug looks far better then the welds on the hacked trap door attempt by po that I fixed. I’m slowly getting the hang of welding with no prior experience before this project.
Everything welded in and undercoated. The weld on the plug looks far better then the welds on the hacked trap door attempt by po that I fixed. I’m slowly getting the hang of welding with no prior experience before this project.
0 2024/09/26 20:08:15
Plug ready to weld in
Plug ready to weld in
0 2024/09/26 20:08:11