Third Generation F-Body Message Boards
0 2015/04/17 14:09:21
0 2015/04/17 14:09:41
0 2015/04/17 14:09:49
0 2015/04/17 14:09:56
0 2015/04/17 14:10:22
0 2015/04/20 11:29:12
0 2015/04/20 11:29:37
Epoxy primer. Down to bare metal.
Epoxy primer. Down to bare metal.
0 2015/05/28 11:18:32
This work was done in 08'
This work was done in 08'
0 2015/05/28 11:18:59
About a month after this I was in an accident that caused my baby to sit in storage till hopefully this year.
About a month after this I was in an accident that caused my baby to sit in storage till hopefully this year.
0 2015/05/28 11:19:11
T-Top bar was dented bad. I wanted the car done perfect.
T-Top bar was dented bad. I wanted the car done perfect.
0 2015/05/28 11:19:59
0 2015/06/02 09:37:31
0 2015/08/09 12:50:24
0 2015/08/20 06:29:48
0 2015/08/20 07:24:55
0 2015/08/20 09:03:46
0 2015/08/22 11:55:25
0 2015/08/22 11:55:55
0 2015/08/23 09:09:12
0 2015/08/23 09:47:51
0 2015/08/23 09:48:05
0 2015/08/26 19:01:00
0 2015/09/08 10:20:30
This is where you find your #s
This is where you find your #s
0 2015/09/14 09:40:21
Heads.....
Heads.....
0 2015/09/14 09:40:34
Example............
Example............
0 2015/09/14 09:41:18
So nice!
So nice!
0 2015/09/18 14:03:05
This is whats inside.
This is whats inside.
0 2015/11/22 09:58:05
Here is where you can find the #. Remember it doesnt really mean anything tho. You dont know if its been bored, decked, so who knows what you really have.
Here is where you can find the #. Remember it doesnt really mean anything tho. You dont know if its been bored, decked, so who knows what you really have.
0 2015/11/26 09:11:25
0 2015/12/13 09:46:59
0 2015/12/13 09:48:44
WWII Diamond T Tank Transport
WWII Diamond T Tank Transport
0 2016/02/12 21:41:52
0 2016/07/02 12:03:06
Got it to shop. Very dirty. Makes me want to cry. The place I keep it in storage is off a dirt road. It will never be this dirty again. :)
Got it to shop. Very dirty. Makes me want to cry. The place I keep it in storage is off a dirt road. It will never be this dirty again. :)
0 2016/07/03 20:42:55
Unloading from trailer. You can see the dent it acquired being in storage. Of course no one knows anything... Hope the body guy can fix it easily. Rather not spend more in time and labor than another used door would cost. I would really like to keep the original door. Car has only 84k on it. Very clean. No rust anywhere.
Unloading from trailer. You can see the dent it acquired being in storage. Of course no one knows anything... Hope the body guy can fix it easily. Rather not spend more in time and labor than another used door would cost. I would really like to keep the original door. Car has only 84k on it. Very clean. No rust anywhere.
0 2016/07/03 20:43:02
Starting to pull engine. I think I'm going to find a A.C delete for more room. If anyone has one to sell, PM me please.
Starting to pull engine. I think I'm going to find a A.C delete for more room. If anyone has one to sell, PM me please.
0 2016/07/03 20:43:18
Definatly going to put a different pitcock on the radiator. A style where a guy can slip a hose over so radiator fluid doesnt run down the core support and drip out of every hole. Jacked under tire to tip car to prevent fluid running. Really dont like spilling anything on the ground.
Definatly going to put a different pitcock on the radiator. A style where a guy can slip a hose over so radiator fluid doesnt run down the core support and drip out of every hole. Jacked under tire to tip car to prevent fluid running. Really dont like spilling anything on the ground.
0 2016/07/03 20:43:29
Got most the parts off to ease removal. Headers are a pain. 1/8 of a turn from top side, 1/8 a turn from the bottom side. Defiantly going to look for a bolt with a smaller shoulder on them or turn the shoulder down in my lathe. I ordered some arp's and I ope they fit. Also in the market for some new headers. Mine are fine, just a very tight fit and I had to customize the collector to get it to aim back. Want a style that fits better and is readily available to replace if they go bad.
Got most the parts off to ease removal. Headers are a pain. 1/8 of a turn from top side, 1/8 a turn from the bottom side. Defiantly going to look for a bolt with a smaller shoulder on them or turn the shoulder down in my lathe. I ordered some arp's and I ope they fit. Also in the market for some new headers. Mine are fine, just a very tight fit and I had to customize the collector to get it to aim back. Want a style that fits better and is readily available to replace if they go bad.
0 2016/07/03 20:44:00
I dont know how you guys do it, but up here in MN, this is how we pull our engines. Makes it breeze. Tran and all. You can stand the engine straight up if needed.
I dont know how you guys do it, but up here in MN, this is how we pull our engines. Makes it breeze. Tran and all. You can stand the engine straight up if needed.
0 2016/07/03 20:44:32
She's out and separated from tran. Mounting on engine stand, pulling block drains to empty radiator fluid. In the market for converter bolts. I cant find them anywhere. At least for a 700r4.. Preferably ARP.
She's out and separated from tran. Mounting on engine stand, pulling block drains to empty radiator fluid. In the market for converter bolts. I cant find them anywhere. At least for a 700r4.. Preferably ARP.
0 2016/07/03 20:44:44