Third Generation F-Body Message Boards
0 2018/02/17 15:56:35
0 2018/02/17 15:56:53
0 2018/02/17 15:57:09
0 2018/02/17 15:57:22
0 2018/02/17 15:57:34
0 2018/02/17 15:57:44
0 2018/02/17 15:57:54
mocking it up in stock form...in stock configuration the bottom of the air box hits everyting
mocking it up in stock form...in stock configuration the bottom of the air box hits everyting
0 2018/02/17 16:26:21
Starting modification...First, cutting off the end at the throttle body to pull it away from the radiator.
Starting modification...First, cutting off the end at the throttle body to pull it away from the radiator.
0 2018/02/17 16:27:14
Cleaned up my cut, now it just needs a new rubber couple to connect to TB
Cleaned up my cut, now it just needs a new rubber couple to connect to TB
0 2018/02/17 16:28:25
Looks good, just needs a coupler now.
Looks good, just needs a coupler now.
0 2018/02/17 16:29:07
Look how nice the stock air box looks in there!! Almost factory. But, I'll still need to cut off the bottom of that large air box.
Look how nice the stock air box looks in there!! Almost factory. But, I'll still need to cut off the bottom of that large air box.
0 2018/02/17 16:30:06
Cutting off the flange part of the Air Box so that I can still snap the Air Filter on...I had to spend quite a bit of time cleaning up my terrible cut LOL
Cutting off the flange part of the Air Box so that I can still snap the Air Filter on...I had to spend quite a bit of time cleaning up my terrible cut LOL
0 2018/02/17 16:31:18
Here is the flange I needed off the Air Box to snap the air filter under the remaining air box.
Here is the flange I needed off the Air Box to snap the air filter under the remaining air box.
0 2018/02/17 16:32:24
0 2018/02/17 16:33:02
Snapped the flange onto bottom of air box...the idea is that the air flow is open from underneath, coming from radiator support area
Snapped the flange onto bottom of air box...the idea is that the air flow is open from underneath, coming from radiator support area
0 2018/02/17 16:33:19
I think this looks pretty trick...
I think this looks pretty trick...
0 2018/02/17 16:34:07
So I'll need about a 6" piece to extend to box, plus a 90 coupler.
So I'll need about a 6" piece to extend to box, plus a 90 coupler.
0 2018/02/17 16:34:36
Added a coupler to clamp to the throttle body
Added a coupler to clamp to the throttle body
0 2018/02/18 20:30:52
Clamped to throttle body
Clamped to throttle body
0 2018/02/18 20:31:43
Cutting off stock air box to make room for the K&N cone filter
Cutting off stock air box to make room for the K&N cone filter
0 2018/02/18 20:32:20
Used hose clamp for a guide to cut tube
Used hose clamp for a guide to cut tube
0 2018/02/18 20:32:56
What's left of the tube, with MAF mount
What's left of the tube, with MAF mount
0 2018/02/18 20:33:10
Clamped to main intake tube
Clamped to main intake tube
0 2018/02/18 20:33:24
Installed K&N cone filter
Installed K&N cone filter
0 2018/02/18 20:33:35
Installation complete!
Installation complete!
0 2018/02/18 20:33:54
Cutting of stock radiator plastic hose "rest"
Cutting of stock radiator plastic hose "rest"
0 2018/02/25 08:26:11
"rest" removed
"rest" removed
0 2018/02/25 08:26:28
new 4" couple goes onto throttle body end of 5th gen tube (I previously cut tube to bring it in).
new 4" couple goes onto throttle body end of 5th gen tube (I previously cut tube to bring it in).
0 2018/02/25 08:26:38
Looks at home on the throttle body!
Looks at home on the throttle body!
0 2018/02/25 08:26:48
Next, cut that factory 5th gen air box off to make room for the K&N filter.
Next, cut that factory 5th gen air box off to make room for the K&N filter.
0 2018/02/25 08:26:57
Nice piece from stock intake that has the MAF boss built in.
Nice piece from stock intake that has the MAF boss built in.
0 2018/02/25 08:27:08
clamped on MAF tube into stock coubpler.
clamped on MAF tube into stock coubpler.
0 2018/02/25 08:27:15
Installed 4" x 7" K&N cone air filter
Installed 4" x 7" K&N cone air filter
0 2018/02/25 08:27:28
This will get me started...later I may add a 45 elbow and another 6" straight tube to send it closer to the radiator support.
This will get me started...later I may add a 45 elbow and another 6" straight tube to send it closer to the radiator support.
0 2018/02/25 08:27:37
Cut off the plastic radiator hose support "rest" to make room
Cut off the plastic radiator hose support "rest" to make room
0 2018/02/25 08:32:35
new 4" coupler to throttle body, I cut off the factory 5th gen tube coupler to bring the intake away from radiator and closer to TB
new 4" coupler to throttle body, I cut off the factory 5th gen tube coupler to bring the intake away from radiator and closer to TB
0 2018/02/25 08:32:53
Cut the 5th gen air box off to make room for new K&N filter
Cut the 5th gen air box off to make room for new K&N filter
0 2018/02/25 08:33:04
Installed MAF tube into stock tube coupler
Installed MAF tube into stock tube coupler
0 2018/02/25 08:33:16
installed K&N filter
installed K&N filter
0 2018/02/25 08:33:26