Third Generation F-Body Message Boards
i took this from the Unbalanced Engineering site; rear LCA's with the angle changed like i have should only make it better, no?
i took this from the Unbalanced Engineering site; rear LCA's with the angle changed like i have should only make it better, no?
0 2017/05/30 12:20:09
0 2018/06/27 06:23:12
0 2018/06/27 06:23:21
at the track with splitter and wing for the first time
at the track with splitter and wing for the first time
0 2018/11/21 05:24:35
IROC with Splitter and Wing
IROC with Splitter and Wing
0 2018/11/21 05:25:56
IROC at the track, first time with Splitter and Wing
IROC at the track, first time with Splitter and Wing
0 2018/11/21 05:27:09
IROC at the track with Splitter and Wing
IROC at the track with Splitter and Wing
0 2018/11/21 05:29:16
0 2018/11/21 05:45:20
0 2019/07/06 18:29:49
0 2019/07/06 18:29:55
0 2019/07/06 18:30:00
0 2019/07/06 18:31:34
0 2019/09/23 15:22:48
0 2019/09/23 15:22:55
0 2019/09/23 15:23:04
Caliper prior to machining. I just used a sharpie and traced the outline of the bracket onto the caliper, then milled to the line I drew - did it at lunchtime!
Caliper prior to machining. I just used a sharpie and traced the outline of the bracket onto the caliper, then milled to the line I drew - did it at lunchtime!
0 2019/09/23 15:45:57
0 2019/09/23 15:46:04
0 2019/09/23 15:47:02
Pre machine Note: OEM 6th Gen brake hose still installed. I had to use the banjo bolt from this hose on the Earls hose to work proper.
Pre machine Note: OEM 6th Gen brake hose still installed. I had to use the banjo bolt from this hose on the Earls hose to work proper.
0 2019/09/23 15:57:20
Post machine with bracket for comparison
Post machine with bracket for comparison
0 2019/09/23 15:57:31
Perfect fit!
Perfect fit!
0 2019/09/23 15:57:38
Zinc chromate primer for corrosion protection
Zinc chromate primer for corrosion protection
0 2019/09/23 15:57:43
Note 15mm spacer with ARP studs and 1LE bearings as ordered from BBU.
Note 15mm spacer with ARP studs and 1LE bearings as ordered from BBU.
0 2019/11/12 06:38:19
OEM roller cam, 86-up SBC motors
OEM roller cam, 86-up SBC motors
0 2020/11/07 14:12:05
Specs from GMPP web site
Specs from GMPP web site
0 2020/11/07 14:14:55
I’m by myself at the track and either driving it or getting ready to drive it, I don’t have a photo guy - .sorry for the crappy trailer pic lol
I’m by myself at the track and either driving it or getting ready to drive it, I don’t have a photo guy - .sorry for the crappy trailer pic lol
0 2020/11/10 07:56:24
0 2021/08/01 20:54:51
0 2021/08/01 20:54:57
0 2021/08/01 20:55:04
0 2021/08/01 20:55:09
0 2021/08/01 20:55:14
0 2021/08/01 20:55:20
I used MAPP gas to heat it up before denting
I used MAPP gas to heat it up before denting
0 2021/08/01 21:01:51
0 2021/08/01 21:04:31
Note where I cut the pipes and put in an angle to fit the collector width
Note where I cut the pipes and put in an angle to fit the collector width
0 2021/10/03 17:11:23
I flattened the tube a bit so it fit in the oval bit
I flattened the tube a bit so it fit in the oval bit
0 2021/10/03 17:12:00
It ain’t going to be pretty. More work is required to get it proper
It ain’t going to be pretty. More work is required to get it proper
0 2021/10/03 17:12:21
Made a transition on the oval pipe itself by cutting a wedge out of it
Made a transition on the oval pipe itself by cutting a wedge out of it
0 2021/10/03 17:12:33
Stage 1, getting the X pipe to fit on the collectors.
Stage 1, getting the X pipe to fit on the collectors.
0 2021/10/03 17:12:45
0 2021/10/03 17:13:04