Third Generation F-Body Message Boards
0 2021/02/24 20:15:54
0 2021/02/24 20:21:04
0 2021/02/24 20:21:21
0 2021/02/24 20:24:57
0 2021/03/01 10:37:01
0 2021/03/01 18:04:48
0 2021/03/01 18:05:05
0 2021/03/01 18:05:24
0 2021/03/01 18:05:50
0 2021/03/01 18:06:16
0 2021/03/01 18:37:15
0 2021/03/01 18:43:28
0 2021/03/01 18:43:55
0 2021/03/03 08:02:00
0 2021/03/03 11:48:54
0 2021/03/03 11:49:09
0 2021/03/03 11:51:32
0 2021/03/03 11:52:03
0 2021/03/03 11:52:14
I put a light coat of this adhesion promoter on the back sides of the moldings....and give it about 5 min to dry
I put a light coat of this adhesion promoter on the back sides of the moldings....and give it about 5 min to dry
0 2021/03/03 15:31:14
I use this 3M two sided molding tape. 7/8" wide
I use this 3M two sided molding tape. 7/8" wide
0 2021/03/03 15:32:24
It comes in a big roll...
It comes in a big roll...
0 2021/03/03 15:33:48
Here it is applied. It takes a little trimming with a razor blade on the one end. The big door pieces don't need any special trimming. When they're ready to be installed, you just peel off the red protective layer to expose the sticky side
Here it is applied. It takes a little trimming with a razor blade on the one end. The big door pieces don't need any special trimming. When they're ready to be installed, you just peel off the red protective layer to expose the sticky side
0 2021/03/03 15:34:20
And it's ready to be installed when the time comes. I will also use the adhesion promoter on the car when i reinstall them.
And it's ready to be installed when the time comes. I will also use the adhesion promoter on the car when i reinstall them.
0 2021/03/03 15:36:54
This is what the Snap-On Crud Thug looks like. It's expensive, and it takes a big air compressor to run it, but it's a MUST HAVE tool for doing this. The little eraser wheels that you put in a drill work....well, sort of. This process would take hours with one of those, and with this tool takes minutes
This is what the Snap-On Crud Thug looks like. It's expensive, and it takes a big air compressor to run it, but it's a MUST HAVE tool for doing this. The little eraser wheels that you put in a drill work....well, sort of. This process would take hours with one of those, and with this tool takes minutes
0 2021/03/03 17:21:30
0 2021/03/06 20:56:43
0 2021/03/06 21:13:53
0 2021/03/06 21:14:03
0 2021/03/20 16:17:20
0 2021/03/20 16:17:37
0 2021/03/20 16:17:51
0 2021/03/20 16:18:06
0 2021/03/20 16:51:11
0 2021/03/20 16:55:02
0 2021/03/20 16:57:31
0 2021/03/21 10:01:29
0 2021/03/21 10:01:41
0 2021/03/21 10:01:51
0 2021/03/21 18:21:53
0 2021/03/21 18:22:10