Third Generation F-Body Message Boards
0 2020/11/20 21:01:58
0 2020/11/20 21:01:54
0 2020/11/20 21:01:51
0 2020/11/20 21:01:46
0 2020/11/20 21:01:42
0 2020/11/20 21:01:38
0 2020/11/20 21:01:34
0 2020/11/20 21:01:30
0 2020/11/20 21:01:25
0 2020/11/20 21:01:21
0 2020/11/20 21:01:16
0 2020/11/20 21:01:12
0 2020/11/20 21:01:07
0 2020/11/20 19:50:29
0 2020/11/20 19:50:25
0 2020/11/20 19:50:19
0 2020/11/20 19:50:15
0 2020/11/20 19:50:10
0 2020/11/20 19:50:05
0 2020/11/20 19:50:00
Getting closer to finishing the front end. Just need konis and rotors. šŸ˜Ž
Getting closer to finishing the front end. Just need konis and rotors. šŸ˜Ž
0 2019/04/17 08:22:21
Only one I have at the moment. They arenā€™t pitted or warped.
Only one I have at the moment. They arenā€™t pitted or warped.
0 2019/03/31 16:54:08
0 2019/03/23 06:03:44
0 2019/03/23 06:03:19
0 2019/02/22 15:38:53
0 2019/02/22 15:38:47
0 2019/02/22 15:38:40
0 2019/02/22 15:38:31
0 2019/02/22 15:38:24
0 2019/02/16 16:04:34
0 2019/02/16 16:04:09
0 2019/02/16 16:04:04
0 2019/02/16 15:54:49
0 2019/02/16 09:23:39
Finished up 90% of the harness tear down. I still have the trans harness I left mostly intact because I couldnā€™t figure out how to separate the blue connector as it was slightly different than the other black j1 and gray j2. Since I didnā€™t remove this harness and I donā€™t have an 08+ to look at Iā€™m going to have to figure out which sensors are which and what I can completely eliminate. For those that have done a gen 4 ls swap did you run new grounds or keep that one large ground harness intact?
Finished up 90% of the harness tear down. I still have the trans harness I left mostly intact because I couldnā€™t figure out how to separate the blue connector as it was slightly different than the other black j1 and gray j2. Since I didnā€™t remove this harness and I donā€™t have an 08+ to look at Iā€™m going to have to figure out which sensors are which and what I can completely eliminate. For those that have done a gen 4 ls swap did you run new grounds or keep that one large ground harness intact?
0 2019/02/04 16:26:03
Made some brackets for the front set up for the Brembos. Still need to open the spindle holes to their final size and then Powdercoat them. Iā€™m about to order 1LE rotors to turn down to hubs and then Iā€™ll start on the rear set up when I get my hands on a 4th gen rear end. I used the brackets from Luke Skaffs website and burned them out on a plasma table out of 3/8ā€ plate.
Made some brackets for the front set up for the Brembos. Still need to open the spindle holes to their final size and then Powdercoat them. Iā€™m about to order 1LE rotors to turn down to hubs and then Iā€™ll start on the rear set up when I get my hands on a 4th gen rear end. I used the brackets from Luke Skaffs website and burned them out on a plasma table out of 3/8ā€ plate.
0 2019/02/02 08:52:39
0 2019/01/27 17:43:05
0 2019/01/27 17:43:04
0 2019/01/27 17:42:56
0 2019/01/26 16:58:54