Third Generation F-Body Message Boards
0 2025/06/19 16:41:28
0 2023/09/14 10:51:01
0 2023/09/14 10:50:50
0 2023/07/11 16:26:51
0 2023/07/11 16:26:49
upper mount from the back, have to notch around the higher fan.
upper mount from the back, have to notch around the higher fan.
0 2023/07/11 16:26:46
the upper mount
the upper mount
0 2023/07/11 16:26:44
Here's a pic of the bottom mount. It's fastened to the fan housing with rivnuts, the two tapped holes align with holes that are already in the lower radiator support tray from the factory
Here's a pic of the bottom mount. It's fastened to the fan housing with rivnuts, the two tapped holes align with holes that are already in the lower radiator support tray from the factory
0 2023/07/11 16:26:41
0 2023/07/06 15:41:18
0 2023/07/06 15:41:16
0 2023/02/12 13:03:03
0 2022/11/25 17:19:04
0 2022/11/19 14:55:03
0 2022/11/19 14:53:12
0 2022/11/19 14:53:10
0 2022/11/19 14:53:07
Here it is freshly sprayed with epoxy primer, hoping to do base coat clear coat within the next week or two and then finally get the new gaskets in
Here it is freshly sprayed with epoxy primer, hoping to do base coat clear coat within the next week or two and then finally get the new gaskets in
0 2022/10/21 19:06:36
0 2022/10/21 19:06:35
more filler was needed than this but didn't grab a pic
more filler was needed than this but didn't grab a pic
0 2022/10/21 19:06:34
Here's the section nearly ready for paint
Here's the section nearly ready for paint
0 2022/10/21 19:06:32
the patch blended in
the patch blended in
0 2022/10/21 18:42:00
welded in, ugly sheet metal welds but there was a gap and they're getting ground down anyways
welded in, ugly sheet metal welds but there was a gap and they're getting ground down anyways
0 2022/10/21 18:41:58
patch panel in place, fitment wasn't ideal
patch panel in place, fitment wasn't ideal
0 2022/10/21 18:41:56
Here's the back side nasty part cut out
Here's the back side nasty part cut out
0 2022/10/21 18:41:53
Here it is welded in and coated with more weld thru primer
Here it is welded in and coated with more weld thru primer
0 2022/10/21 18:34:48
different view of the other side
different view of the other side
0 2022/10/21 18:34:46
You can see the shrinking marks on the panel, a couple more tweaks after this and it fit well
You can see the shrinking marks on the panel, a couple more tweaks after this and it fit well
0 2022/10/21 18:34:44
This is how I shaped the sheet metal going under the front t top channel, did the same for the back channel as well
This is how I shaped the sheet metal going under the front t top channel, did the same for the back channel as well
0 2022/10/21 18:34:41
Here's that panel welded in, I did some hammer and smoothing work after this but don't have any pictures
Here's that panel welded in, I did some hammer and smoothing work after this but don't have any pictures
0 2022/10/21 18:31:13
Here's the replacement patch I made for that section, I unfortunately don't have pictures but I used a shrinker and stretcher set I got from harbor freight to match the curve, rounded the edge over to match the curve of the roof
Here's the replacement patch I made for that section, I unfortunately don't have pictures but I used a shrinker and stretcher set I got from harbor freight to match the curve, rounded the edge over to match the curve of the roof
0 2022/10/21 18:31:11
I removed the bad sheet metal from the picture prior to this, cleaned up the metal under neath, and cut out the rotted metal on the front roof section itself
I removed the bad sheet metal from the picture prior to this, cleaned up the metal under neath, and cut out the rotted metal on the front roof section itself
0 2022/10/21 18:31:09
Same goes for the back
Same goes for the back
0 2022/10/21 18:29:46
This is the front without the channel, the metal underneath also needed to be replaced
This is the front without the channel, the metal underneath also needed to be replaced
0 2022/10/21 18:29:42
Here's the back channel also partially ripped up
Here's the back channel also partially ripped up
0 2022/10/21 18:26:04
the passenger side
the passenger side
0 2022/10/21 18:26:02
Here's the front channel partially ripped up, showing the damage under neath
Here's the front channel partially ripped up, showing the damage under neath
0 2022/10/21 18:25:59
This was the worst section of the front channel, as you can tell in the pic it rotted the inside face of the t top section as well
This was the worst section of the front channel, as you can tell in the pic it rotted the inside face of the t top section as well
0 2022/10/21 18:25:57
0 2020/01/24 12:12:58
0 2019/10/23 19:54:19
0 2019/10/23 19:54:11