Third Generation F-Body Message Boards
0 2020/05/03 11:09:59
0 2020/05/03 10:19:05
0 2020/05/03 10:18:52
0 2020/05/03 09:32:39
0 2020/05/03 09:32:13
Nicly centered but maybe too deep.
Nicly centered but maybe too deep.
0 2020/05/03 07:42:44
0 2020/05/02 15:35:20
0 2020/05/02 15:34:59
0 2020/05/02 15:34:25
Got this from my tran guy. There are other ways but unless you have xray vision, you need to see where the plunger is. It also will confirm if your geometry is correct based on how far the plunger moves.
Got this from my tran guy. There are other ways but unless you have xray vision, you need to see where the plunger is. It also will confirm if your geometry is correct based on how far the plunger moves.
0 2020/04/25 18:16:40
0 2020/04/23 07:34:58
Room to move in.
Room to move in.
0 2020/04/23 07:34:25
More room than i thought I'd have.
More room than i thought I'd have.
0 2020/04/23 07:33:59
0 2020/04/23 07:33:30
0 2020/04/22 18:24:06
0 2020/04/22 18:22:58
0 2020/04/22 18:22:08
My torque arm will be tighter, you can see there is room to scoot it even closer if necessary. Im also making my own torque arm mount. Not sure yet if it will tie into the trans mount. Definitely not going on tail of tran.
My torque arm will be tighter, you can see there is room to scoot it even closer if necessary. Im also making my own torque arm mount. Not sure yet if it will tie into the trans mount. Definitely not going on tail of tran.
0 2020/04/22 18:21:16
Plenty of room
Plenty of room
0 2020/04/22 18:20:42
New 8.8
New 8.8
0 2020/04/22 18:20:16
Old 7.5
Old 7.5
0 2020/04/22 18:19:35
Got my trans and tc back so thats in also. Cant wait to be driving tho ive still got a ways to go.
Got my trans and tc back so thats in also. Cant wait to be driving tho ive still got a ways to go.
0 2020/04/22 18:17:43
0 2020/04/08 19:47:13
0 2020/04/08 19:46:57
0 2020/04/08 19:46:34
0 2020/04/08 19:46:16
0 2020/04/08 19:44:56
0 2020/04/08 19:44:32
Its ok, getting better. Surprisingly this cast welds clean, nice puddle, wet wo crap floating in it. Its just hard to weld something thats 500 deg. U cant touch it. And the heat coming of it is like a grill. If i do this again, i will make a separate platform for my tig hand to run across. This was welded around 200 amps.
Its ok, getting better. Surprisingly this cast welds clean, nice puddle, wet wo crap floating in it. Its just hard to weld something thats 500 deg. U cant touch it. And the heat coming of it is like a grill. If i do this again, i will make a separate platform for my tig hand to run across. This was welded around 200 amps.
0 2020/04/08 09:20:51
Welded tje entire length on bottom side. Took all night for it to cool. Was still 70 deg in the morning.
Welded tje entire length on bottom side. Took all night for it to cool. Was still 70 deg in the morning.
0 2020/04/08 09:20:31
Hahaha, this adds 10hp ya know.
Hahaha, this adds 10hp ya know.
0 2020/04/08 09:20:01
My tc came. Long story but these guys are fantastic to work with. If you want a bad ass tc with out breaking the bank..
My tc came. Long story but these guys are fantastic to work with. If you want a bad ass tc with out breaking the bank..
0 2020/04/08 09:19:47
My bunt cake im making.
My bunt cake im making.
0 2020/04/06 13:40:26
Great book.
Great book.
0 2020/04/06 13:40:09
Depth of penetration
Depth of penetration
0 2020/04/06 13:39:52
Top left corner, you can see the penetration. This is a actual piece of the 8.8 i cut off. The weld actually failed as there is still weld on both pieces.
Top left corner, you can see the penetration. This is a actual piece of the 8.8 i cut off. The weld actually failed as there is still weld on both pieces.
0 2020/04/06 13:39:37
Towels worked great. Think it took 2 hours before it was 80*. I waited till it was 70 before unwrapping.
Towels worked great. Think it took 2 hours before it was 80*. I waited till it was 70 before unwrapping.
0 2020/04/04 16:53:16
And same on this side. Was going great till i dunked the tungsten. Doh!
And same on this side. Was going great till i dunked the tungsten. Doh!
0 2020/04/04 16:52:58
Weldeing around a radius sucks. Im happy with these. Was going great till i dunked the tungsten. Lol
Weldeing around a radius sucks. Im happy with these. Was going great till i dunked the tungsten. Lol
0 2020/04/04 16:52:41
This one laid down nice. Walked the cup.
This one laid down nice. Walked the cup.
0 2020/04/04 16:52:16