Third Generation F-Body Message Boards
315/30 18’s on 10” rims.
315/30 18’s on 10” rims.
0 2023/10/19 15:49:56
Angle alum extrusion used to measure - touching rim only
Angle alum extrusion used to measure - touching rim only
0 2023/10/19 15:49:41
Front alum spacer
Front alum spacer
0 2023/10/19 15:49:14
Steel shim .151” OEM SPACER and hun centric alum spacer
Steel shim .151” OEM SPACER and hun centric alum spacer
0 2023/10/19 15:48:33
Rear spacing - shows both spacers
Rear spacing - shows both spacers
0 2023/10/19 15:48:21
0 2023/08/17 16:29:56
0 2023/08/17 16:22:04
0 2023/08/17 16:19:23
0 2023/08/17 16:18:32
0 2023/08/17 16:08:24
0 2023/08/17 16:08:15
0 2023/08/17 16:08:08
0 2023/08/17 16:01:32
0 2023/08/17 16:01:27
Painted with high heat paint and ready for installation
Painted with high heat paint and ready for installation
0 2021/10/17 19:16:46
It’s finally in position! I’m ok with how it worked out. It’s not perfect but it will work as intended
It’s finally in position! I’m ok with how it worked out. It’s not perfect but it will work as intended
0 2021/10/03 17:13:23
0 2021/10/03 17:13:04
Stage 1, getting the X pipe to fit on the collectors.
Stage 1, getting the X pipe to fit on the collectors.
0 2021/10/03 17:12:45
Made a transition on the oval pipe itself by cutting a wedge out of it
Made a transition on the oval pipe itself by cutting a wedge out of it
0 2021/10/03 17:12:33
It ain’t going to be pretty. More work is required to get it proper
It ain’t going to be pretty. More work is required to get it proper
0 2021/10/03 17:12:21
I flattened the tube a bit so it fit in the oval bit
I flattened the tube a bit so it fit in the oval bit
0 2021/10/03 17:12:00
Note where I cut the pipes and put in an angle to fit the collector width
Note where I cut the pipes and put in an angle to fit the collector width
0 2021/10/03 17:11:23
0 2021/08/01 21:04:31
I used MAPP gas to heat it up before denting
I used MAPP gas to heat it up before denting
0 2021/08/01 21:01:51
0 2021/08/01 20:55:20
0 2021/08/01 20:55:14
0 2021/08/01 20:55:09
0 2021/08/01 20:55:04
0 2021/08/01 20:54:57
0 2021/08/01 20:54:51
I’m by myself at the track and either driving it or getting ready to drive it, I don’t have a photo guy - .sorry for the crappy trailer pic lol
I’m by myself at the track and either driving it or getting ready to drive it, I don’t have a photo guy - .sorry for the crappy trailer pic lol
0 2020/11/10 07:56:24
Specs from GMPP web site
Specs from GMPP web site
0 2020/11/07 14:14:55
OEM roller cam, 86-up SBC motors
OEM roller cam, 86-up SBC motors
0 2020/11/07 14:12:05
Note 15mm spacer with ARP studs and 1LE bearings as ordered from BBU.
Note 15mm spacer with ARP studs and 1LE bearings as ordered from BBU.
0 2019/11/12 06:38:19
Zinc chromate primer for corrosion protection
Zinc chromate primer for corrosion protection
0 2019/09/23 15:57:43
Perfect fit!
Perfect fit!
0 2019/09/23 15:57:38
Post machine with bracket for comparison
Post machine with bracket for comparison
0 2019/09/23 15:57:31
Pre machine Note: OEM 6th Gen brake hose still installed. I had to use the banjo bolt from this hose on the Earls hose to work proper.
Pre machine Note: OEM 6th Gen brake hose still installed. I had to use the banjo bolt from this hose on the Earls hose to work proper.
0 2019/09/23 15:57:20
0 2019/09/23 15:47:02
0 2019/09/23 15:46:04