Third Generation F-Body Message Boards
0 2019/06/23 14:53:54
0 2019/06/08 03:19:50
0 2019/05/19 12:33:24
0 2019/05/19 12:30:29
first time out of the garage under its own power. Dont mind the fan, just trying to keep it cool.
first time out of the garage under its own power. Dont mind the fan, just trying to keep it cool.
0 2019/05/10 18:00:39
amazon washer fluid bottle. I didnt want the big bulky one there as eventually my intake filter will be in this area
amazon washer fluid bottle. I didnt want the big bulky one there as eventually my intake filter will be in this area
0 2019/05/10 17:59:54
Hurst Shifter installed
Hurst Shifter installed
0 2019/05/10 17:59:21
a big mess of wires. this will all be loomed and hidden under the dash.
a big mess of wires. this will all be loomed and hidden under the dash.
0 2019/04/14 03:25:40
This is what im using for wire loom
This is what im using for wire loom
0 2019/04/14 03:25:32
4th gen coolant reservoir
4th gen coolant reservoir
0 2019/04/14 03:25:26
Hole cut for shifter. Got a deal on a hurst shifter so once that arrives ill be able to put the interior back together.
Hole cut for shifter. Got a deal on a hurst shifter so once that arrives ill be able to put the interior back together.
0 2019/04/14 03:25:17
Cable holder
Cable holder
0 2019/04/05 11:08:57
This is where the adjuster attaches to the cables
This is where the adjuster attaches to the cables
0 2019/04/05 11:08:10
Engine is in! Trans is in too but I didn't take any pictures yet!
Engine is in! Trans is in too but I didn't take any pictures yet!
0 2019/03/15 08:20:20
Painted accessories
Painted accessories
0 2019/03/10 08:09:39
4th gen rear in. Lowering springs, panhard bar and LCAs also installed
4th gen rear in. Lowering springs, panhard bar and LCAs also installed
0 2019/03/10 08:09:32
Distributor and balancer installed. I ended up painting the balancer black.
Distributor and balancer installed. I ended up painting the balancer black.
0 2019/03/10 08:09:26
0 2019/03/04 15:25:35
0 2019/03/04 15:24:56
0 2019/03/04 15:22:17
0 2019/03/04 15:20:28
0 2019/03/04 15:20:19
0 2019/03/04 15:19:36
0 2019/03/04 15:18:02
0 2019/03/04 15:05:51
0 2019/03/04 15:04:56
0 2019/03/04 15:04:16
0 2019/03/04 15:03:46
0 2019/02/22 17:32:14
Following pockets directions on making an LT1 harness. I took the original harness apart and am laying each sensor harness on individually . I'm just about done that step, then I'll add ignition power and the rest of the grounds. That'll take care of the bulk of the lt1 harness.
Following pockets directions on making an LT1 harness. I took the original harness apart and am laying each sensor harness on individually . I'm just about done that step, then I'll add ignition power and the rest of the grounds. That'll take care of the bulk of the lt1 harness.
0 2019/02/14 12:33:58
0 2019/02/04 15:18:16
0 2019/02/03 16:47:11
0 2019/02/03 16:46:53
0 2019/02/03 16:42:39
Painted strut mounts and heater box too
Painted strut mounts and heater box too
0 2019/02/03 16:16:19
0 2019/02/03 16:15:56
Cable
Cable
0 2019/01/28 12:31:56
Air cleaner
Air cleaner
0 2019/01/28 12:31:12
0 2019/01/28 12:30:08
0 2019/01/28 11:31:34