Third Generation F-Body Message Boards
1 2019/02/07 10:18:56
335 30 X 18's under factory fenders
335 30 X 18's under factory fenders
1 2019/02/01 11:12:01
0 2026/02/15 19:17:22
0 2026/02/15 19:17:21
0 2026/02/15 19:17:19
0 2026/02/15 19:17:17
0 2026/02/15 19:17:16
the factory covered this large expanse of plastic with carpeting, but molding was needed to address all the complex curves
the factory covered this large expanse of plastic with carpeting, but molding was needed to address all the complex curves
0 2025/11/23 11:52:52
the transition from the leather covered tubs is too obvious
the transition from the leather covered tubs is too obvious
0 2025/11/23 11:52:45
looks a bit sterile....
looks a bit sterile....
0 2025/11/23 11:52:14
a firebird GTA the way they should have built it
a firebird GTA the way they should have built it
0 2025/01/06 12:19:47
0 2025/01/06 12:19:29
0 2025/01/06 12:19:20
Here she sits, doesn't get driven a whole lot.....
Here she sits, doesn't get driven a whole lot.....
0 2024/12/08 09:47:55
0 2024/12/08 09:47:43
0 2024/12/07 18:00:36
0 2024/12/07 18:00:20
0 2022/12/24 08:32:16
the aforementioned 'new' door panel
the aforementioned 'new' door panel
0 2022/09/06 18:23:21
0 2022/09/06 18:22:20
0 2022/09/03 16:04:09
0 2022/09/03 15:59:50
0 2022/02/27 18:09:24
the way they should have built it......
the way they should have built it......
0 2022/01/03 21:21:57
stock handle fastener, then.....
stock handle fastener, then.....
0 2022/01/03 21:21:31
notice the stainless fastener where the factory rivet used to be
notice the stainless fastener where the factory rivet used to be
0 2022/01/03 21:20:10
the button has to be 'tuned' to slide easily in the handle opening
the button has to be 'tuned' to slide easily in the handle opening
0 2022/01/03 21:18:58
the wear on the plastic really shows after it gets pointed out
the wear on the plastic really shows after it gets pointed out
0 2022/01/03 21:18:11
brushing with some 400grit really gave it a 'stock' look. might polish it later, see how it looks
brushing with some 400grit really gave it a 'stock' look. might polish it later, see how it looks
0 2022/01/03 21:16:53
after trimming down to size, i was getting much happier with it
after trimming down to size, i was getting much happier with it
0 2022/01/03 21:13:24
the rough cut was just some 6061 flat stock 3/8" thick cut to shape
the rough cut was just some 6061 flat stock 3/8" thick cut to shape
0 2022/01/03 21:11:49
after disassembly, the old button was pressed on, and I wanted a little more security, so i threaded the end of the rod for the new button
after disassembly, the old button was pressed on, and I wanted a little more security, so i threaded the end of the rod for the new button
0 2022/01/03 21:10:22
that push button was a deal breaker here. had to do something else.
that push button was a deal breaker here. had to do something else.
0 2022/01/03 21:09:36
this was the third piece of leather before i got it right
this was the third piece of leather before i got it right
0 2022/01/03 21:08:52
two needles at opposite ends of the thread, and you really have to pull hard
two needles at opposite ends of the thread, and you really have to pull hard
0 2022/01/03 21:08:05
Getting the shape perfect here is the only way to ensure this seam is straight when you sart pulling thread
Getting the shape perfect here is the only way to ensure this seam is straight when you sart pulling thread
0 2022/01/03 21:06:59
back in '82.....
back in '82.....
0 2021/11/15 08:05:15
my first third gen with the Products Guild IMSA hood
my first third gen with the Products Guild IMSA hood
0 2021/11/06 21:12:45
0 2021/11/02 14:14:06
0 2021/11/02 14:13:53