Third Generation F-Body Message Boards
0 2023/04/01 19:44:57
0 2023/04/01 19:44:54
0 2023/04/01 19:44:50
0 2022/11/19 21:06:19
0 2022/11/19 21:06:11
0 2022/11/19 21:06:03
0 2022/11/19 21:05:57
0 2022/11/19 21:05:50
0 2022/11/19 21:05:42
0 2022/11/19 21:05:36
0 2022/11/19 20:09:19
0 2022/11/19 20:09:12
0 2022/11/19 20:09:05
0 2022/11/19 20:08:58
0 2022/11/19 19:45:59
0 2022/11/19 19:45:56
0 2022/11/19 19:30:25
resin 3D printed LS3 and t56
resin 3D printed LS3 and t56
0 2022/11/19 19:30:20
0 2022/11/19 19:30:17
scribed and painted in the ttops
scribed and painted in the ttops
0 2022/11/19 19:30:13
0 2022/11/19 19:30:10
0 2022/11/19 19:30:06
I plan to use 85 Z28 bumper covers and gfx on mine so that's why I used a 85 Z28 kit
I plan to use 85 Z28 bumper covers and gfx on mine so that's why I used a 85 Z28 kit
0 2022/11/19 19:30:03
had to remove the lower firewall here. It will make it a lot easier to repair the inner fender flange and remove one of the previous owners booger welds from trying to brace the frame for the z bar.
had to remove the lower firewall here. It will make it a lot easier to repair the inner fender flange and remove one of the previous owners booger welds from trying to brace the frame for the z bar.
0 2022/11/19 18:34:19
0 2022/11/19 18:34:10
removed inner filler panel and now have a bluetooth rocker panel (not really, the whole car is braced, I made sure to add a brace to the rocker before I cut all of this stuff out so it doesn't move.
removed inner filler panel and now have a bluetooth rocker panel (not really, the whole car is braced, I made sure to add a brace to the rocker before I cut all of this stuff out so it doesn't move.
0 2022/11/19 18:34:06
removed the A-pillar panel
removed the A-pillar panel
0 2022/11/19 18:34:02
0 2022/11/19 18:33:58
0 2022/11/19 18:33:53
A-pillar/inner rocker corner
A-pillar/inner rocker corner
0 2022/11/19 18:33:50
it's really bad, I know
it's really bad, I know
0 2022/11/19 18:33:47
drivers floor is a mess
drivers floor is a mess
0 2022/11/19 18:33:43
0 2022/11/19 18:33:39
made sure the doubler plate still fit
made sure the doubler plate still fit
0 2022/11/19 18:33:35
fixing the bottom of the frame. I welded it on the inside and outside so I could grind it smooth on the outside so it looked correct.
fixing the bottom of the frame. I welded it on the inside and outside so I could grind it smooth on the outside so it looked correct.
0 2022/11/19 18:33:31
3/8 weld nuts welded onto the new 16 gauge doubler plate
3/8 weld nuts welded onto the new 16 gauge doubler plate
0 2022/11/19 18:33:28
old driver doubler plate
old driver doubler plate
0 2022/11/19 18:33:23
Turned the car around to start on the driver side. There was a hole in the frame under the trans mount so I had to fix that
Turned the car around to start on the driver side. There was a hole in the frame under the trans mount so I had to fix that
0 2022/11/19 18:33:19
0 2022/11/19 18:33:14
epoxied
epoxied
0 2022/11/19 18:33:10