Third Generation F-Body Message Boards
Also completed installing exhaust, just waiting on a few clamps
Also completed installing exhaust, just waiting on a few clamps
0 2021/05/25 17:59:21
0 2021/05/25 17:57:32
Also used my tube bender to create an air tube for the cat up to the air system.
Also used my tube bender to create an air tube for the cat up to the air system.
0 2021/05/25 17:56:04
0 2021/05/25 17:54:11
Sure enough, measured with a business card at 2.5 inches versus 3 inches I was going for
Sure enough, measured with a business card at 2.5 inches versus 3 inches I was going for
0 2021/05/25 17:52:31
Noticed in this picture that the ID of the cat is severely necked down.
Noticed in this picture that the ID of the cat is severely necked down.
0 2021/05/25 17:50:51
Left off here. Thanks for watching.
Left off here. Thanks for watching.
0 2021/05/23 17:14:12
I realize could change with everything on the ground, but so far so good!
I realize could change with everything on the ground, but so far so good!
0 2021/05/23 17:13:07
Looks like will be OK
Looks like will be OK
0 2021/05/23 17:12:04
A little worried about tire rub
A little worried about tire rub
0 2021/05/23 17:11:09
Started installing exhaust from Y-pipe
Started installing exhaust from Y-pipe
0 2021/05/23 17:10:14
Driveshaft torqued
Driveshaft torqued
0 2021/05/23 17:08:24
Flywheel cover in
Flywheel cover in
0 2021/05/23 17:07:32
Drive shaft in
Drive shaft in
0 2021/05/23 17:06:50
0 2021/05/23 17:05:59
0 2021/05/23 17:02:54
Sanded all the surface rust and painted the drive shaft
Sanded all the surface rust and painted the drive shaft
0 2021/05/23 17:01:35
Pressure washed all remaining grungy brackets, shrouds and hoses for re-assy.
Pressure washed all remaining grungy brackets, shrouds and hoses for re-assy.
0 2021/05/23 16:59:47
Cinched up nice an tight, no slippage out of the hole, and not visible.
Cinched up nice an tight, no slippage out of the hole, and not visible.
0 2021/05/23 16:58:20
0 2021/05/23 16:49:32
0 2021/05/23 16:47:35
Sorry to pollute the thread, but it was a beautiful Pontiac!
Sorry to pollute the thread, but it was a beautiful Pontiac!
0 2021/05/22 16:57:01
Here is the passenger side, not as bad, but please confirm I have installed correctly. Thanks
Here is the passenger side, not as bad, but please confirm I have installed correctly. Thanks
0 2021/05/20 16:55:37
This is the drivers side, noticed the bleed valve is tucked away making it very hard to install a bleed tube and operate the nut. Do I have it on right? Hoping I got them switched?? Forgive my naivete.
This is the drivers side, noticed the bleed valve is tucked away making it very hard to install a bleed tube and operate the nut. Do I have it on right? Hoping I got them switched?? Forgive my naivete.
0 2021/05/20 16:52:37
Passenger side cinched up good to go so far.
Passenger side cinched up good to go so far.
0 2021/05/20 16:51:25
0 2021/05/20 16:50:58
Had to wait for a different tailpipe clamp to install the rest of the Y-pipe, but success!
Had to wait for a different tailpipe clamp to install the rest of the Y-pipe, but success!
0 2021/05/20 16:48:51
That was easy! I was looking for my transmission cross brace and couldn't find it. Once I unstacked everything off the boat, I finally found it. And I still have spare counter space to boot.
That was easy! I was looking for my transmission cross brace and couldn't find it. Once I unstacked everything off the boat, I finally found it. And I still have spare counter space to boot.
0 2021/05/20 16:40:23
0 2021/05/20 16:38:23
0 2021/05/20 16:37:52
I will post dimensions and cut angles if any one is interested. One other comment is that you can easily make a scaffold out of it with a simple addition. You can slide up and down in any position and just screw to to secure. Throw on a 2x8 or 2x12 and make a very stable work platform.
I will post dimensions and cut angles if any one is interested. One other comment is that you can easily make a scaffold out of it with a simple addition. You can slide up and down in any position and just screw to to secure. Throw on a 2x8 or 2x12 and make a very stable work platform.
0 2021/05/20 16:34:04
Now all I have to do is get the engine running and bleed the brakes and I can DRIVE!!!
Now all I have to do is get the engine running and bleed the brakes and I can DRIVE!!!
0 2021/05/19 17:52:14
0 2021/05/19 17:51:42
So cool, one day closer, really
So cool, one day closer, really
0 2021/05/19 17:49:12
You can see the broken chunk still residing where the evaporator goes. Should have listened to TL and removed it for painting!!
You can see the broken chunk still residing where the evaporator goes. Should have listened to TL and removed it for painting!!
0 2021/05/18 17:47:08
Finally around 4:30 I can mash the gas pedal and get WOT on the throttle bodies!!!! Oh happy day!!!
Finally around 4:30 I can mash the gas pedal and get WOT on the throttle bodies!!!! Oh happy day!!!
0 2021/05/18 17:40:20
Finally almost 1pm got motor mounts installed
Finally almost 1pm got motor mounts installed
0 2021/05/18 17:39:00
Had to remove the distributor cap for clearance
Had to remove the distributor cap for clearance
0 2021/05/18 17:38:08
Like SpongeBob, 2 hours later...
Like SpongeBob, 2 hours later...
0 2021/05/18 17:36:48
0 2021/05/18 17:36:14