Third Generation F-Body Message Boards
Factory front GTA wheel with a .1776 wheel spacer at full lock and full droop
Factory front GTA wheel with a .1776 wheel spacer at full lock and full droop
0 2022/08/15 17:32:52
Factory front GTA wheel with no spacer, full lock and full droop, with the weight of the car on the front suspension there maybe plenty of clearance
Factory front GTA wheel with no spacer, full lock and full droop, with the weight of the car on the front suspension there maybe plenty of clearance
0 2022/08/15 17:31:58
And some rivets to make sure the reducer doesn’t move
And some rivets to make sure the reducer doesn’t move
0 2022/08/15 14:28:56
Using a heat gun to make the brake duct plastic a little more pliable it fits pretty snug
Using a heat gun to make the brake duct plastic a little more pliable it fits pretty snug
0 2022/08/15 14:28:51
The size difference is real close
The size difference is real close
0 2022/08/15 14:28:44
0 2022/08/13 16:34:39
For the inlet to the ZO6 brake ducts im waiting on these to come in, the measurements list in the Amazon add seem to be the right size for what is needed, their supposed to be here on Monday
For the inlet to the ZO6 brake ducts im waiting on these to come in, the measurements list in the Amazon add seem to be the right size for what is needed, their supposed to be here on Monday
0 2022/08/13 16:34:37
Picture is of the driver side wheel with the coil spring compressed using a floor jack, wheel was raised until the frame started to lift off of the jack stand. I’m running 1000lb front coil springs on weight jacks with a 36mm sway bar so im h go ping for a flat turning car with very little body roll, I won’t really know if this enough clearance until I get this car on the road again.
Picture is of the driver side wheel with the coil spring compressed using a floor jack, wheel was raised until the frame started to lift off of the jack stand. I’m running 1000lb front coil springs on weight jacks with a 36mm sway bar so im h go ping for a flat turning car with very little body roll, I won’t really know if this enough clearance until I get this car on the road again.
0 2022/08/13 16:34:34
And to cover the hole a 7/8” plug, found these at Lowes in the hardware aisle.
And to cover the hole a 7/8” plug, found these at Lowes in the hardware aisle.
0 2022/08/13 16:34:29
Two stainless steel #14 x 3/4” sheet metals
Two stainless steel #14 x 3/4” sheet metals
0 2022/08/13 16:34:23
Checking both sides this spot on the brake ducts and the body where both similar in flat spots for the brake duct to sit flat against the body.
Checking both sides this spot on the brake ducts and the body where both similar in flat spots for the brake duct to sit flat against the body.
0 2022/08/13 16:34:17
Felt a second mounting point was necessary
Felt a second mounting point was necessary
0 2022/08/13 16:34:11
0 2022/08/13 16:34:04
Aluminum extension installed, due to the difference in shapes of the ZO6 brake duct and the aluminum ring I squeezed some expanding foam to help as much air to the calipers.
Aluminum extension installed, due to the difference in shapes of the ZO6 brake duct and the aluminum ring I squeezed some expanding foam to help as much air to the calipers.
0 2022/08/13 16:33:58
In the picture above you can see the aluminum tubing is somewhat square, and in this picture you can see difference in the shape. I’m using 6-32 nylock nuts
In the picture above you can see the aluminum tubing is somewhat square, and in this picture you can see difference in the shape. I’m using 6-32 nylock nuts
0 2022/08/13 16:33:52
3” OD aluminum tube cut to 1” long, 4 holes drilled to 9/64” for 6-32 stainless steel screws.
3” OD aluminum tube cut to 1” long, 4 holes drilled to 9/64” for 6-32 stainless steel screws.
0 2022/08/13 16:33:45
Probably gonna cut these about where I’m showing in the pic above. Gonna need a 4”-3” reducer, I’ll see what our local hardware stores have this weekend
Probably gonna cut these about where I’m showing in the pic above. Gonna need a 4”-3” reducer, I’ll see what our local hardware stores have this weekend
0 2022/08/11 20:24:18
The outlet is under sized for a 3” hose and it’s an odd shape and I expect it being problematic trying hose clamp the 3” hose. I’m going to rivet a 3” OD X 1-1 1/2” long aluminum tube to this side so the hose clamp has something more to grab onto, similar to the picture below.
The outlet is under sized for a 3” hose and it’s an odd shape and I expect it being problematic trying hose clamp the 3” hose. I’m going to rivet a 3” OD X 1-1 1/2” long aluminum tube to this side so the hose clamp has something more to grab onto, similar to the picture below.
0 2022/08/11 20:24:17
0 2022/08/11 20:11:14
Looking down from top of the tire
Looking down from top of the tire
0 2022/08/11 20:11:09
0 2022/08/11 20:10:37
0 2022/08/11 20:10:31
0 2022/08/11 18:00:07
0 2022/08/11 17:59:55
0 2022/08/11 17:59:29
0 2022/08/11 17:59:15
0 2022/08/11 17:58:50
0 2022/08/11 17:58:37
0 2022/08/11 17:58:20
0 2022/08/11 16:22:59
0 2022/08/09 10:31:12
0 2022/08/09 10:18:48
0 2022/08/09 07:28:52
0 2022/08/09 07:17:51
0 2022/08/09 07:17:49
0 2022/08/09 07:17:45
0 2022/08/09 07:17:43
0 2022/08/04 11:00:30
0 2022/08/04 10:58:35
0 2022/08/04 10:58:24