Third Generation F-Body Message Boards
Side view
Side view
0 2016/08/01 20:34:59
Garage door foam double sided tapped.
Garage door foam double sided tapped.
0 2016/08/01 20:34:49
0 2016/07/29 09:42:22
0 2016/07/29 09:42:02
0 2016/07/26 20:17:48
0 2016/07/26 20:17:45
0 2016/07/26 20:17:40
0 2016/07/26 20:17:33
0 2016/07/26 20:14:32
0 2016/07/26 20:14:20
Stock 5.3, remove engine cover and swap or use OeM small case alternator. Everything clears.
Stock 5.3, remove engine cover and swap or use OeM small case alternator. Everything clears.
0 2016/07/18 08:24:40
0 2016/07/11 21:54:48
0 2016/07/11 21:54:36
0 2016/07/11 21:54:29
IAT sensor on the right , EGT on the left and bottom left is BOV. That's the farthest the probe would go in.
IAT sensor on the right , EGT on the left and bottom left is BOV. That's the farthest the probe would go in.
0 2016/06/15 21:59:34
0 2016/06/15 21:36:08
0 2016/06/15 21:36:00
0 2016/06/15 21:35:53
0 2016/06/15 21:35:46
0 2016/06/15 21:35:37
Close up back shot of under car. 4" is still pretty loud only on the throttle honestly at idle it's very quiet and I suppose the dual mufflers help :)
Close up back shot of under car. 4" is still pretty loud only on the throttle honestly at idle it's very quiet and I suppose the dual mufflers help :)
0 2016/06/15 21:30:50
Another one. Trans pan is next lowest part.
Another one. Trans pan is next lowest part.
0 2016/06/15 21:30:37
Side shot of exhaust. U can see the Asa's collectors in the left. They are the lowest part of the whole exhaust and everything tucked up higher than stock. This is with a driveshaft safety loop.
Side shot of exhaust. U can see the Asa's collectors in the left. They are the lowest part of the whole exhaust and everything tucked up higher than stock. This is with a driveshaft safety loop.
0 2016/06/15 21:30:27
For those wondering what ground clearance was with SS long tubes, dual 3" into single 4" over axle with dual mufflers and lowered. I honestly couldn't scrape it if I wanted too lol
For those wondering what ground clearance was with SS long tubes, dual 3" into single 4" over axle with dual mufflers and lowered. I honestly couldn't scrape it if I wanted too lol
0 2016/06/15 21:30:17
Close up of the BAER black label 13" setup, love them! Esp with a hydroboost!
Close up of the BAER black label 13" setup, love them! Esp with a hydroboost!
0 2016/06/15 21:30:10
0 2016/06/14 14:11:02
0 2016/06/14 14:10:59
0 2016/06/14 14:10:55
0 2016/06/08 20:25:20
0 2016/06/08 20:25:15
0 2016/06/07 20:19:30
0 2016/06/07 20:19:21
0 2016/06/07 20:19:16
0 2016/06/07 20:19:08
0 2016/06/07 20:19:03
New spacer mockup and IAT location. Figuring out nozzle placement for drilling and tapping. It's tight.
New spacer mockup and IAT location. Figuring out nozzle placement for drilling and tapping. It's tight.
0 2016/06/07 20:12:47
EGR block off plate with IAT sensor installed.
EGR block off plate with IAT sensor installed.
0 2016/06/07 20:12:42
IAT location looking inside TB opening. Open cage style and sits in recess of airflow path so it might not get "wet" from meth injection and skew readings.
IAT location looking inside TB opening. Open cage style and sits in recess of airflow path so it might not get "wet" from meth injection and skew readings.
0 2016/06/07 20:12:37
Black one also had a step that fit inside intake opening which decreased TB opening size... No good.
Black one also had a step that fit inside intake opening which decreased TB opening size... No good.
0 2016/06/07 20:12:31
New billet spacer vs plastic black one which was only 1/2" thick.
New billet spacer vs plastic black one which was only 1/2" thick.
0 2016/06/07 20:12:27