Third Generation F-Body Message Boards
Looking good. Still need final block sanding.
Looking good. Still need final block sanding.
0 2023/07/15 09:04:56
0 2023/07/15 08:56:51
This is how the doors look now after 2 coats of heavy fill primer. There are some small air holes visible that I'll have to fill with spot putty before i block sand them, but definitely heading in the right direction.
This is how the doors look now after 2 coats of heavy fill primer. There are some small air holes visible that I'll have to fill with spot putty before i block sand them, but definitely heading in the right direction.
0 2023/07/15 08:52:28
Lots of filler, sanding, fiiler and sanding. These doirs were given to me free, so i didnt feel bad about cutting them up. Thet were however in rough shape, with multiple dents from being kicked to close and being repainted twice.
Lots of filler, sanding, fiiler and sanding. These doirs were given to me free, so i didnt feel bad about cutting them up. Thet were however in rough shape, with multiple dents from being kicked to close and being repainted twice.
0 2023/07/15 08:48:02
Sheet metal panels installed and interior door handle mounted. In keeping with my "home brew" budget build, the metal panels are made from salvaged sheet metal shelving units.
Sheet metal panels installed and interior door handle mounted. In keeping with my "home brew" budget build, the metal panels are made from salvaged sheet metal shelving units.
0 2023/07/15 08:43:29
Interior side of door showing sub-structure that mounts interior door handle.
Interior side of door showing sub-structure that mounts interior door handle.
0 2023/07/15 08:41:23
A little work with a bfh was all that i needed to get frame clearance so steering could go lock to lock without interference. Now I'm swinging 295/35/18 tires through a 4th gen Z28 turning radius. Im sure i could clear 305/30/18 and possibly 315/30/18.
A little work with a bfh was all that i needed to get frame clearance so steering could go lock to lock without interference. Now I'm swinging 295/35/18 tires through a 4th gen Z28 turning radius. Im sure i could clear 305/30/18 and possibly 315/30/18.
0 2023/06/28 10:26:03
0 2023/06/28 10:21:49
Here you can see the difference in the bent spindle(rear), and non bent(front). The top half of the rear spindle is bent up towards the rotor. The top half of the front spindle lays flat, near parallel to the floor
Here you can see the difference in the bent spindle(rear), and non bent(front). The top half of the rear spindle is bent up towards the rotor. The top half of the front spindle lays flat, near parallel to the floor
0 2023/06/28 09:58:11
0 2023/06/28 09:55:42
Left side clearance after spacer. Left side has noticeably more clearance than the right side. Something isnt right.
Left side clearance after spacer. Left side has noticeably more clearance than the right side. Something isnt right.
0 2023/06/28 09:40:39
This is clearance on right front after 1/2" spacer and longer studs.
This is clearance on right front after 1/2" spacer and longer studs.
0 2023/06/28 09:36:05
Right front tire just touches upper balljoint stud.
Right front tire just touches upper balljoint stud.
0 2023/06/28 09:33:29
0 2023/06/28 09:32:18
0 2023/06/28 09:29:43
Looks pretty good with the 10.5x18 Z06 wheels.
Looks pretty good with the 10.5x18 Z06 wheels.
0 2023/06/28 09:27:57
0 2023/03/16 20:34:38
0 2023/03/16 17:48:17
0 2022/12/29 13:10:15
Cables attached to my calipers with no problem. Clamped cable to rear axle tube flange.
Cables attached to my calipers with no problem. Clamped cable to rear axle tube flange.
0 2022/12/29 13:10:06
Rear cables enter through rear firewall behind drivers seat.
Rear cables enter through rear firewall behind drivers seat.
0 2022/12/29 13:09:57
0 2022/12/29 13:09:46
Black bracket welded to trans tunnel anchors front cable housing.
Black bracket welded to trans tunnel anchors front cable housing.
0 2022/12/29 13:09:34
Factory parking brake lever mounted to floor just to the left of the brake proportioning valve.
Factory parking brake lever mounted to floor just to the left of the brake proportioning valve.
0 2022/12/29 13:09:21
0 2022/12/29 12:47:42
0 2022/12/29 12:47:35
0 2022/12/29 12:47:28
0 2022/12/29 12:47:21
0 2022/12/29 12:20:23
0 2022/12/29 12:20:21
0 2022/12/29 12:20:20
0 2022/12/29 12:20:17
0 2022/12/27 14:39:18
0 2022/12/27 14:39:11
0 2022/12/27 14:39:03
0 2022/12/27 14:29:16
0 2022/12/27 12:35:28
0 2022/12/27 12:35:22
0 2022/12/27 12:35:14
0 2022/12/27 12:30:09