IROC/Z28 Plastic Hood Louvers
02-22-2011, 11:54 PM
#1
Supreme Member
Thread Starter
iTrader: (25)
Join Date: Sep 2005
Location: NJ
Posts: 1,823
Received 281 Likes
on
219 Posts
Car: 1987 IROC-Z
Engine: 406 on N20 w/ EFI
Transmission: P.B. 700R4
Axle/Gears: 12 bolt w/ 3.91
IROC/Z28 Plastic Hood Louvers
..edit..whoops forgot to list my location.. New Jersey
I am selling a pair of black plastic hood louvers that go on the 1985-1990 iroc-z/Z28 style hood. they are in great condition. not faded at all. there is only one small hazy part on one fin of a louver,, which should easily buff out or wet-sand out. 90% of the tabs on the underside are there. these were off a clean red iroc (not mine) and are in great shape. i have no use for these since i have a fiberglass cowl hood.
asking $150.00 plus shipping (unless you would like to pick them up) **they sell for $200 A PIECE in Classic Industries and other similar catalogues. (part # G6808 and part # G6809) i am selling the PAIR for less than the cost of one of the ones offered elsewhere. located 20 mins from bridgewater and 20 mins from morristown areas of NJ
photos below
also selling a used stock 3rd gen torque arm $10 obo
also... unused Lakewood bolt-in drive shaft loop specific for 3rd gen fbodys $15.00
I am selling a pair of black plastic hood louvers that go on the 1985-1990 iroc-z/Z28 style hood. they are in great condition. not faded at all. there is only one small hazy part on one fin of a louver,, which should easily buff out or wet-sand out. 90% of the tabs on the underside are there. these were off a clean red iroc (not mine) and are in great shape. i have no use for these since i have a fiberglass cowl hood.
asking $150.00 plus shipping (unless you would like to pick them up) **they sell for $200 A PIECE in Classic Industries and other similar catalogues. (part # G6808 and part # G6809) i am selling the PAIR for less than the cost of one of the ones offered elsewhere. located 20 mins from bridgewater and 20 mins from morristown areas of NJ
photos below
also selling a used stock 3rd gen torque arm $10 obo
also... unused Lakewood bolt-in drive shaft loop specific for 3rd gen fbodys $15.00
Last edited by IROCZman15; 02-23-2011 at 12:02 AM.
04-29-2011, 01:52 PM
#3
Supreme Member
Thread Starter
iTrader: (25)
Join Date: Sep 2005
Location: NJ
Posts: 1,823
Received 281 Likes
on
219 Posts
Car: 1987 IROC-Z
Engine: 406 on N20 w/ EFI
Transmission: P.B. 700R4
Axle/Gears: 12 bolt w/ 3.91
Re: IROC/Z28 Plastic Hood Louvers
if you want em, you can have them. i was all setup to sell them to a guy in pa... and derspite numerous attempts at an exchange, i have no heard from him in 3 weeks.
you can have them for the above price, plus shipping. which i'd estimate to be $25 ( i got a price quote for $5 from nj to pa) so its about that price.
let me know. pm me or email .
you can have them for the above price, plus shipping. which i'd estimate to be $25 ( i got a price quote for $5 from nj to pa) so its about that price.
let me know. pm me or email .
04-30-2011, 09:15 AM
#5
Junior Member
iTrader: (5)
Join Date: Jan 2011
Location: Little Falls, New York
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Camaro Iroc-z
Engine: 305 TPI
Transmission: 700R4
Re: IROC/Z28 Plastic Hood Louvers
Not sure if that email worked. Just send one to joe.konik@gmail.com or pm me. Thanks!
05-11-2011, 08:49 PM
#6
Supreme Member
Thread Starter
iTrader: (25)
Join Date: Sep 2005
Location: NJ
Posts: 1,823
Received 281 Likes
on
219 Posts
Car: 1987 IROC-Z
Engine: 406 on N20 w/ EFI
Transmission: P.B. 700R4
Axle/Gears: 12 bolt w/ 3.91
Re: IROC/Z28 Plastic Hood Louvers
sold. please close this thread
hope the louvers look great on the car man
hope the louvers look great on the car man
Thread
Thread Starter
Forum
Replies
Last Post
Hotrodboba400
Firebirds for Sale
3
12-10-2019 07:07 PM
