[IA] '89 RS Roller
#1
Supreme Member
Thread Starter
iTrader: (1)
Join Date: Nov 2003
Location: Davenport, Iowa
Posts: 1,598
Likes: 0
Received 2 Likes
on
2 Posts
Car: Still a 3rd Gen
Engine: 450HP 355
Transmission: TH350
Axle/Gears: 9" with 4.11's
'89 RS Roller
Car is located in Davenport, IA a few minutes from I-74
$2500 Cash/Paypal/Cashiers Check.
Clean Title
1989 RS
Auto
Gunmetal Metallic (original color)
Black interior
Power locks/Manual windows.
Power steering
Nice Clarion deck/speakers
B&M Megashifter w/new HD Cable
4" Fiberglass Harwood hood with a sweet mural of the Grim Reaper
16x8 IROC wheels
Aluminum driveshaft w/new U-joints
Freshly rebuilt 4.10 Posi rear end, Disk brakes ('87 IROC), Fresh Auburn 3 series carrier, Richmond gears. TA Performance diff girdle/cover.
UMI Tubular Lower Control Arms
New Founders lower control arm relocation brackets
New Hooker Supercomp catback (3" to dual 2.5") with all new hangers (less than 200 miles)
New Spohn Tubular K member
New front struts
New rear shocks
New front brakes, rotors and bearings
New steering drag link
New 255LPH pump in the tank, new fuel filter with AN adapters and braided stainless running up to the engine bay.
New V8 radiator
New trans cooler
Fresh alignment in 2011
Fiberglass sub box for 2 12's if the buyer wants it
Car just needs your engine and trans!
Thanks for looking!
$2500 Cash/Paypal/Cashiers Check.
Clean Title
1989 RS
Auto
Gunmetal Metallic (original color)
Black interior
Power locks/Manual windows.
Power steering
Nice Clarion deck/speakers
B&M Megashifter w/new HD Cable
4" Fiberglass Harwood hood with a sweet mural of the Grim Reaper
16x8 IROC wheels
Aluminum driveshaft w/new U-joints
Freshly rebuilt 4.10 Posi rear end, Disk brakes ('87 IROC), Fresh Auburn 3 series carrier, Richmond gears. TA Performance diff girdle/cover.
UMI Tubular Lower Control Arms
New Founders lower control arm relocation brackets
New Hooker Supercomp catback (3" to dual 2.5") with all new hangers (less than 200 miles)
New Spohn Tubular K member
New front struts
New rear shocks
New front brakes, rotors and bearings
New steering drag link
New 255LPH pump in the tank, new fuel filter with AN adapters and braided stainless running up to the engine bay.
New V8 radiator
New trans cooler
Fresh alignment in 2011
Fiberglass sub box for 2 12's if the buyer wants it
Car just needs your engine and trans!
Thanks for looking!
Last edited by DeathStarr89; 08-19-2013 at 09:29 AM.
#3
Supreme Member
Thread Starter
iTrader: (1)
Join Date: Nov 2003
Location: Davenport, Iowa
Posts: 1,598
Likes: 0
Received 2 Likes
on
2 Posts
Car: Still a 3rd Gen
Engine: 450HP 355
Transmission: TH350
Axle/Gears: 9" with 4.11's
Re: '89 RS Roller
Sure, no problem.
The hatch and back seat are full of extra parts (spare arm wrests, the aluminum driveshaft, the catback, etc...).
The HVAC controls and the bezel are in the hatch, you can kind of see the Clarion deck sitting on the passenger floor. Weather permitting i'll go ahead and install that stuff again.
If there is anything specific anyone wants pics of just let me know.
BTW, the odometer says 78K. I've been unable to find out yet if it's rolled over or not.
Thanks
The hatch and back seat are full of extra parts (spare arm wrests, the aluminum driveshaft, the catback, etc...).
The HVAC controls and the bezel are in the hatch, you can kind of see the Clarion deck sitting on the passenger floor. Weather permitting i'll go ahead and install that stuff again.
If there is anything specific anyone wants pics of just let me know.
BTW, the odometer says 78K. I've been unable to find out yet if it's rolled over or not.
Thanks
#4
Supreme Member
Thread Starter
iTrader: (1)
Join Date: Nov 2003
Location: Davenport, Iowa
Posts: 1,598
Likes: 0
Received 2 Likes
on
2 Posts
Car: Still a 3rd Gen
Engine: 450HP 355
Transmission: TH350
Axle/Gears: 9" with 4.11's
Re: '89 RS Roller
Quick bump, I'm sure someone out there is looking for a good roller!
Thread
Thread Starter
Forum
Replies
Last Post
KO1
Engine/Drivetrain/Suspension Parts for Sale
16
10-15-2015 05:00 PM