how do you remove seats from 92 Convertable
#1
how do you remove seats from 92 Convertable
Hi, can anyone tell me how to remove the seats from my 92 rs convertable, back seats especially i have seats from a 91 and they are power is there a plug under the seats i have now to plug them into? thanks for all your help folks!
#2
Senior Member
Join Date: Mar 2009
Location: 47798 Germany
Posts: 505
Likes: 0
Received 0 Likes
on
0 Posts
Car: '89 RS camaro 305 TBI
Engine: LO3
Transmission: 700R4
Axle/Gears: yep, has those too (stock)
Re: how do you remove seats from 92 Convertable
![Smilie](https://www.thirdgen.org/forums/images/smilies/smile.gif)
Now in all seriousness, the powered seats have a plug underneath the seats. Should be no different for convertibles.
The seats sit on rails. The rails have plastic caps on them. Take off the plastic caps, remove the 4 bolts for the seats, pull them aside (doing the back seats first, then pulling the fronts back should give you space) and unplug the plug.
The back of the rear seats have a bolt in the lower corners left and right, the seats theselves are secured with a single bolt up front. If you have a split rear seat, they still only have 2 bolts. The centre part is just a pin.
Last edited by the solitaire; 07-20-2011 at 02:02 PM.
#3
Re: how do you remove seats from 92 Convertable
the seats in the convertable dont have a plug, how are back seats attached? so there shuodl still be a plug even if there was no power seats to begin with?
#4
Senior Member
Join Date: Mar 2009
Location: 47798 Germany
Posts: 505
Likes: 0
Received 0 Likes
on
0 Posts
Car: '89 RS camaro 305 TBI
Engine: LO3
Transmission: 700R4
Axle/Gears: yep, has those too (stock)
Re: how do you remove seats from 92 Convertable
Just edited my previous post regarding the backseats.
The non-powered fronts have no plugs. I believe the wire harness for powerseats is still there, but only for the drivers side.
The non-powered fronts have no plugs. I believe the wire harness for powerseats is still there, but only for the drivers side.
#5
Junior Member
Join Date: Jan 2010
Location: SoCal
Posts: 74
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 Z28 Convertible, 2000 trans am
Engine: ls6, ls1
Transmission: 4l60e
Re: how do you remove seats from 92 Convertable
There are only two bolts for each rear seat. One just below each seat cushion on the front and one on the outer parts of the back rest. You need to remove the cushions before you can get to the back rests.. if you need pics just let me know.. ill snap a few for you.
#6
Supreme Member
Join Date: Jan 2009
Location: Columbus Ohio
Posts: 1,126
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 Z28,64ImpalaSS4094spd,67 Galaxy
Engine: Dart 415Profiler hd,cmprlrs,Hlly750
Transmission: Built 700R4, 3200 stall
Axle/Gears: 3:89 Moser 9"
Re: how do you remove seats from 92 Convertable
Unbolt them. 4 bolts on each front, 2 bolts on the rear....
Thread
Thread Starter
Forum
Replies
Last Post
1992 Trans Am
History / Originality
27
05-10-2023 07:19 PM
1992 Trans Am
Engine/Drivetrain/Suspension Parts for Sale
1
08-08-2015 08:16 PM