Spoiler holes
#1
Member
Thread Starter
iTrader: (7)
Join Date: Apr 2003
Location: Behind the boathouse
Posts: 210
Likes: 0
Received 0 Likes
on
0 Posts
Car: Huffy 10 speed ;)
Engine: My legs
Transmission: My wrist
Axle/Gears: Little spokey things
Spoiler holes
My Camaro came without any spoiler and I have a 3 peice spoiler for it. Before I poke any holes in my car, I was wondering if anyone knew the measurements for the holes for the side peices. Any help would be appriciated.
#4
Member
Thread Starter
iTrader: (7)
Join Date: Apr 2003
Location: Behind the boathouse
Posts: 210
Likes: 0
Received 0 Likes
on
0 Posts
Car: Huffy 10 speed ;)
Engine: My legs
Transmission: My wrist
Axle/Gears: Little spokey things
Originally posted by gscz28
I got mine off right now, I'll try and get some measurements for ya tomorrow.....
I got mine off right now, I'll try and get some measurements for ya tomorrow.....
#6
Senior Member
iTrader: (2)
Join Date: Feb 2004
Location: Kalamazoo
Posts: 697
Likes: 0
Received 1 Like
on
1 Post
Car: 89 iroc
Engine: 355 TPI FINALLY
Transmission: 700r4/ SHIFT KIT
Axle/Gears: 3.42
alrighty than:
this is what I got.... all measurements are to center of hole, all holes are 1/2 dia.
for the fenders: from the edge of fender by hatch to first hole is 1 1/16, second hole is 6 5/16, third hole is 9". And from back edge and around lip of fender: 1st hole is 2 5/8,2nd hole is 1 1/8, 3rd hole is 7/8.
now the hatch lid: 6 holes, 3 on each side:
1st hole is 1/2 from edge by fender, 2nd hole is 10 7/8, 3rd hole is 18 11/16,
and up from bottom lip: 1st hole 1 9/16, 2nd hole 1 13/16, 3rd hole is 1 15/16.
and same for other side of hatch.....
If your still confused call me tomorrow at work, 800-826-4357 and ask for Greg... I work for Eaton Corp. really no big deal, I take about 100 calls a day ( and thats for real). I'll be there til 8:00pm eastern time... see ya and good luck hope this helps
this is what I got.... all measurements are to center of hole, all holes are 1/2 dia.
for the fenders: from the edge of fender by hatch to first hole is 1 1/16, second hole is 6 5/16, third hole is 9". And from back edge and around lip of fender: 1st hole is 2 5/8,2nd hole is 1 1/8, 3rd hole is 7/8.
now the hatch lid: 6 holes, 3 on each side:
1st hole is 1/2 from edge by fender, 2nd hole is 10 7/8, 3rd hole is 18 11/16,
and up from bottom lip: 1st hole 1 9/16, 2nd hole 1 13/16, 3rd hole is 1 15/16.
and same for other side of hatch.....
If your still confused call me tomorrow at work, 800-826-4357 and ask for Greg... I work for Eaton Corp. really no big deal, I take about 100 calls a day ( and thats for real). I'll be there til 8:00pm eastern time... see ya and good luck hope this helps
Thread
Thread Starter
Forum
Replies
Last Post
Pac J
Tech / General Engine
3
05-17-2020 10:44 AM
Bohemian
Aftermarket Product Review
11
11-25-2015 09:38 PM