prominator parts question
#1
Senior Member
Thread Starter
Join Date: Feb 2005
Location: Rochester,NY
Posts: 617
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1993 Caprice wagon "Shammoo"
Engine: tpi'd 406, with P4 ebl EBL 730 ECM
Transmission: custom "4L65" swap.
Axle/Gears: 3.42:1 with posi
prominator parts question
I have had a Prominator Pro installed now for a few years now. The lack of a permanent mounting has taken it's toll. The remote 8 position dial has been acting up of late and I lose connectivity from time to time. The number on the dial (any number) goes out and the car hiccups as well. It seems the connector pin at the remote box is going.
Does anyone know if Bill is still in business? The Speedtronics info links get returned to me as undeliverable. Anyone got a spare? (send me a PM) Does Mr. Moates now make/sell a replacement? Send him a message as well... no response yet. Any info or ideas you have will be greatly appreciated.
Dave, Rochester NY
Does anyone know if Bill is still in business? The Speedtronics info links get returned to me as undeliverable. Anyone got a spare? (send me a PM) Does Mr. Moates now make/sell a replacement? Send him a message as well... no response yet. Any info or ideas you have will be greatly appreciated.
Dave, Rochester NY
Last edited by lakeffect2; 06-02-2010 at 08:25 AM. Reason: updated info
#2
Senior Member
Thread Starter
Join Date: Feb 2005
Location: Rochester,NY
Posts: 617
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1993 Caprice wagon "Shammoo"
Engine: tpi'd 406, with P4 ebl EBL 730 ECM
Transmission: custom "4L65" swap.
Axle/Gears: 3.42:1 with posi
Re: prominator parts question
Can anyone shed alittle light on this subject for me?
#3
Senior Member
Thread Starter
Join Date: Feb 2005
Location: Rochester,NY
Posts: 617
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1993 Caprice wagon "Shammoo"
Engine: tpi'd 406, with P4 ebl EBL 730 ECM
Transmission: custom "4L65" swap.
Axle/Gears: 3.42:1 with posi
Re: prominator parts question
Still hoping for an answer on this issue. Anyone got some ideas?
#4
Supreme Member
iTrader: (1)
Join Date: Apr 2004
Location: Browns Town
Posts: 3,178
Likes: 0
Received 3 Likes
on
3 Posts
Car: 86 Monte SS (730,$8D,G3,AP,4K,S_V4)
Engine: 406 Hyd Roller 236/242
Transmission: 700R4 HomeBrew, 2.4K stall
Axle/Gears: 3:73 Posi, 7.5 Soon to break
Re: prominator parts question
Post #22 indicates the Moates box should work fine as a replacement.
https://www.thirdgen.org/forums/diy-...mies-like.html
https://www.thirdgen.org/forums/diy-...mies-like.html
#5
Senior Member
Thread Starter
Join Date: Feb 2005
Location: Rochester,NY
Posts: 617
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1993 Caprice wagon "Shammoo"
Engine: tpi'd 406, with P4 ebl EBL 730 ECM
Transmission: custom "4L65" swap.
Axle/Gears: 3.42:1 with posi
Re: prominator parts question
So it seems to be saying that the Prominator uses a part for the display that was supplied by or compatible with products by Moates?
#7
Supreme Member
Join Date: Jul 1999
Location: Baton Rouge, LA, USA
Posts: 1,577
Likes: 0
Received 0 Likes
on
0 Posts
Car: 87 T/A
Engine: 441 SBC 12.5:1 0.680" Lift
Transmission: T-56
Axle/Gears: 4.10 TruTrac Moser 9"
Re: prominator parts question
Shoot me an email offline and I'll be happy to get you taken care of on that.
Thread
Thread Starter
Forum
Replies
Last Post