Clear Connector by ECM???
06-01-2007, 02:34 PM
#1
Member
Thread Starter
Join Date: May 2006
Location: Dayton, Ohio
Posts: 137
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 Firebird
Engine: 6.0L LQ4
Transmission: 4L60E 4000 Stall
Axle/Gears: 3.23 G80 (01 TA)
Clear Connector by ECM???
Alright, I am currently doing a 3.8L swap to my 3.1L Firebird. I am trying to figure out which connector this is. I dont have a picture, but it is part of the Engine Harness by the ECM Connectors. It is a clear connector w/ seven slots in it. It connects to some dash wiring(I believe). I need to know what it is and if anybody can post a diagram of it, that would be great too. Thanks in advance!!
Chris
Chris
06-03-2007, 10:17 AM
#2
Supreme Member
iTrader: (3)
Join Date: Jul 2004
Posts: 2,989
Likes: 0
Received 5 Likes
on
4 Posts
Car: '91 Z28 convertible
Engine: TPI
Transmission: T5
Axle/Gears: 3.27 posi disc
Re: Clear Connector by ECM???
You might be referring to connector C207 but I'm not sure. Do a search here with "C207" and see from the pictures if that's what you are looking at.
If you need the pinouts, we have them on the TechDB page here: http://www.austinthirdgen.org/module...howpage&pid=22 (scroll down to the connector pinouts)
Hope this helps.
Lou
If you need the pinouts, we have them on the TechDB page here: http://www.austinthirdgen.org/module...howpage&pid=22 (scroll down to the connector pinouts)
Hope this helps.
Lou
06-13-2007, 07:47 PM
#3
Member
Thread Starter
Join Date: May 2006
Location: Dayton, Ohio
Posts: 137
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 Firebird
Engine: 6.0L LQ4
Transmission: 4L60E 4000 Stall
Axle/Gears: 3.23 G80 (01 TA)
Re: Clear Connector by ECM???
Ive read that it is C208 or C207. It is black/white. I need a diagram for a 1990, cant seem to find one anywhere
I need the connector end view for it!!
I need the connector end view for it!!
06-13-2007, 10:18 PM
#4
Supreme Member
iTrader: (3)
Join Date: Jul 2004
Posts: 2,989
Likes: 0
Received 5 Likes
on
4 Posts
Car: '91 Z28 convertible
Engine: TPI
Transmission: T5
Axle/Gears: 3.27 posi disc
Re: Clear Connector by ECM???
The C208 would be on the driver side. If you're looking at a connector by the ECM on the pass side, it's most likely the C207. Check the wire colors, that should be a dead giveaway.
Hope this helps.
Lou
Hope this helps.
Lou
06-13-2007, 10:37 PM
#5
Member
Thread Starter
Join Date: May 2006
Location: Dayton, Ohio
Posts: 137
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 Firebird
Engine: 6.0L LQ4
Transmission: 4L60E 4000 Stall
Axle/Gears: 3.23 G80 (01 TA)
Re: Clear Connector by ECM???
Definatly the C207 it's black/white connectors. Idk where I got clear from
I think I found what I need actually skimming through the search for about an hour. Ive had the connector end view for the Grand National Harness and have been searching for this one.
I think I found what I need actually skimming through the search for about an hour. Ive had the connector end view for the Grand National Harness and have been searching for this one.
Thread
Thread Starter
Forum
Replies
Last Post
