TurbomanKnight

Sorry about not posting the pics directly, stupid image limit.

This is all my extra parts laying around my garage. I need to get rid of it as I have no use for them and I'm tired of my dad yelling at me.


1. A Pair of Camaro Door Panels with Plastic Rails.
These were removed from a 91 RS. They will fit all third Gen Camaros. One of the plastic rails are seperating and could be glued back. The panels have no tears in them. The cardboard around where the rail would clip in have been broken but shouldnt be a problem with the panel installed.

$40 For everything. The Rails are worth that much.
http://i16.photobucket.com/albums/b2...e/P7150720.jpg
2. Jegster Driveshaft Safety Loop.
Will not work with an aluminum driveshaft as it will rub. This was on Manolis1969's car.
$20
http://i16.photobucket.com/albums/b2...e/P7150721.jpg

3. Flowmaster 80 Series Muffler
This is new in box and never been installed. Has the 3 inch inlet with dual 2 1/2" outlets.
$80
http://i16.photobucket.com/albums/b2...e/P7150722.jpg
4. 82-84 Trans Am Right Side Tail Light.
Removed from an 83 Trans Am. Housing has one crack on the top of it. But will not show when installed.
$20
http://i16.photobucket.com/albums/b2...e/P7150723.jpg
http://i16.photobucket.com/albums/b2...e/P7150725.jpg

5. 083 SBC TPI 350 Head
This was removed from my 88 IROC-Z. It has been sent out to be checked for cracks and came back good. Head is completely stripped. Good to replace cracked head or to practice porting. Could include valves and springs if desired.
$50
http://i16.photobucket.com/albums/b2...e/P7150728.jpg
http://i16.photobucket.com/albums/b2...e/P7150729.jpg

6. 2 82-85 Firebird or Trans Am Rear Decklid Spoilers
The teal one was removed from an 83 Trans Am. The spoiler has no cracks and comes with the rubber gaskets that sit between the decklid and the spoiler. Missing one stud as it was seized to the car. Can be replaced easiely.

The gray one was installed on a Buick that was donated to my High school. I was able to swipe the spoiler before it was ruined. Needs prime and paint. Has all studs intact but doesnt have the rubber gaskets.

$20 for the Teal one
$15 for the Gray one.
http://i16.photobucket.com/albums/b2...e/P7150730.jpg
http://i16.photobucket.com/albums/b2...e/P7150731.jpg

7. Valves, Valve Springs, Retainers, etc.
These were removed from my 88 IROC 083 heads. They have been mixed up. Good for whatever you feel like doing. They need to be cleaned thoroughly.
$20
http://i16.photobucket.com/albums/b2...e/P7150732.jpg
http://i16.photobucket.com/albums/b2...e/P7150734.jpg

8. 89-92 TPI Runners
These were removed from a 91 Z28. These do not have the provisions for the cold start injector. They can be used on any TPI setup however if your ECM is tuned for a CSI, you need to have the prom reprogrammed. These have no dents on them and can be polished. They might have very minor dings on them. I havent really looked at them.
$50
http://i16.photobucket.com/albums/b2...e/P7150733.jpg
9. Camaro Passenger Kick Panel Gray
Extra one I had laying around it came with a package deal. No cracks or deep scrapes.
$10
http://i16.photobucket.com/albums/b2...e/P7150735.jpg

10. Random Gaskets from FelPro Head Gasket kit.
I ordered this head gasket kit in August '08. I used what I had to out of it. These are the remaining gaskets. Will not piece out. Must take whole. Comes with Valve Seals and O-Rings. Has exhaust manifold gaskets, Valve Cover Gaskets, Timing Cover gaskets and other ones.
$30
http://i16.photobucket.com/albums/b2...e/P7150736.jpg

Prices are Non-negotiable. Can meet up or bring to a meet. Contact me via PM, or my cell at 347-223-6878. If no answer, leave a clear message with your name and number.

Items are located in Brooklyn New York 11208.

-Sam

thirdgenlover

my jasper motor came with casting number 14102193, ive been told these are the swirl port heads. the engine was build for an 87 trans am. would your 88 heads fit on my car.

TurbomanKnight

It would fit. By the way, I am selling only 1 head. The other one had a crack in it so I threw it out.

vetteoz

iTrader: (13)

48 state shipping included in price?

TurbomanKnight

No.


I meant to update that part, you guys can make reasonable offers. Buyer pays shipping. However, I will not ship the cylinder head, or spoilers.

Warrior

iTrader: (1)

How much shipped for the driveshaft loop?

joeEZ

iTrader: (1)

Do you still have the 083 head?