[MN] FS: Complete Serpentine setup for SBC
10-24-2010, 02:15 PM
#1
FS: Complete Serpentine setup for SBC
I have a complete serpentine setup for a small block chevy motor. It is complete with all pullys as well as some accessories. Comes with water pump, alternator, AC compressor all the engine brackets. I also have the AC delete bracket for it if you don 't want to run AC or save on shipping costs. Everything works and is complete and comes with everything you need including the belt. Perfect for a hotrod or converting over your old vbelt. $175.
10-24-2010, 02:21 PM
#2
Member
Join Date: Jun 2010
Location: Hamilton, NJ
Posts: 159
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Pontiac Firebird
Engine: 357ci 400hp 4BBL
Transmission: 700r4
Re: FS: Complete Serpentine setup for SBC
Im not sure about all this pulley lingo, but if I used the ac delete bracket then I wouldn't have to use the ac compressor right. Any pics?
02-01-2011, 10:02 AM
#5
Supreme Member
iTrader: (8)
Join Date: Sep 2004
Location: Charles County, Maryland
Posts: 1,896
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2000 BMW M5
Re: FS: Complete Serpentine setup for SBC
I will take this but I don't want the water pump or the AC compressor- already have new ones and I don't want to pay to ship cores. So I will take just the brackets for $140 + ship if you can ship them ASAP - I screwed up and am halfway through a truck TPI conversion and forgot to get the third gen serp setup ahead of time and now I need to get it back on the road. Please email me at bondospecial@gmail.com with your paypal address
Steve
Steve
02-01-2011, 11:32 PM
#6
Member
Join Date: Dec 2010
Location: Near Wichita Ks
Posts: 331
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1997 K1500 SS/SB
Engine: LT1 with TPI on top
Transmission: 4L60E/np241,
Axle/Gears: 3.73
Re: FS: Complete Serpentine setup for SBC
I will take this but I don't want the water pump or the AC compressor- already have new ones and I don't want to pay to ship cores. So I will take just the brackets for $140 + ship if you can ship them ASAP - I screwed up and am halfway through a truck TPI conversion and forgot to get the third gen serp setup ahead of time and now I need to get it back on the road. Please email me at bondospecial@gmail.com with your paypal address
Steve
Steve
Steve: what year truck you building, I am doing a redo on my 97 with a tpi 350 this time, fried the tpi327
03-01-2011, 03:52 PM
#7
Supreme Member
iTrader: (8)
Join Date: Sep 2004
Location: Charles County, Maryland
Posts: 1,896
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2000 BMW M5
Re: FS: Complete Serpentine setup for SBC
I am just about done, it's a 1988 K1500. I installed a rebuilt L98 350 and did the whole TPI swap using a 6E based setup and repinning the TBI harness over the course of about a month. I kept most emissions (EGR, EVAP, deleted AIR since I am emissions exempt). I have a lot of pics if you are interested in the swap, PM me. Thanks
Thread
Thread Starter
Forum
Replies
Last Post
Terrell351
Engine/Drivetrain/Suspension Parts for Sale
5
06-13-2021 01:13 PM
evilstuie
Tech / General Engine
22
01-09-2020 08:29 PM
