[GA] debating a part out situation. fishing for interest.
#1
Member
Thread Starter
iTrader: (2)
Join Date: Jun 2006
Location: Rocky Face, Ga
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Formula
Engine: 355ci HSR SBC
Transmission: 700r4
Axle/Gears: 3.27
debating a part out situation. fishing for interest.
These parts MAY be up for sale soon.
My budget is running woefully thin.
I got screwed by a local shop, big time. So depending on the cost of repair, I'll be fixing it or parting it. ....1989 formula 350
Nothing listed will be inop/unusable.
Stealth ram, complete.
Profiler 185cc/64cc heads. Hydro springs from profiler good for .650 lift. 2.02 / 1.6 valves. Ran 1 hour.
Comp cams 268xfi. Ran 1 hour.
Comp cams pro mags
comp cams pushrods. Ran 1 hour.
original radiator
Dual fans
2 165 ecm , one "chip" from pcmofnc. For the above spec build.
Gm edge 3000 stall converter.
Built transmission (got it from YenkoST from this board, he had it in a pickup that was around 400+hp)
Good bosch maf
An extra iac valve
A set (front and rear) of never installed kyb gr2 shock/struts.
a new ac delco fuel pump.
A "small" distributor with around 2000 miles on our.
Flow tech headers
The Roller that needs paint and a new rear spoiler so bad.
A water pump and starter with less than 500 miles. (Cheap autozone)
2 sets of valve covers, one tall from summit (chrome), and the stockers.
A msd coil
New ( installed and ran for an hour) set of plugs and ignition wires.
The wiring harness from an 89 formula 350 (some cuts/splices)
Stock intake tubing
ac system is inop, but there is an ac delco blower motor with 500 miles on it.
The block, bought from a guy here bored to .030...... If it is viable.
Speed pro pistons, if they are viable
Stock crank and rods, if viable.
Misc interior bits. Good dash pad.
If you are interested pm me.
Based on interest, I'll update this with prices and all the pertinent info.
My budget is running woefully thin.
I got screwed by a local shop, big time. So depending on the cost of repair, I'll be fixing it or parting it. ....1989 formula 350
Nothing listed will be inop/unusable.
Stealth ram, complete.
Profiler 185cc/64cc heads. Hydro springs from profiler good for .650 lift. 2.02 / 1.6 valves. Ran 1 hour.
Comp cams 268xfi. Ran 1 hour.
Comp cams pro mags
comp cams pushrods. Ran 1 hour.
original radiator
Dual fans
2 165 ecm , one "chip" from pcmofnc. For the above spec build.
Gm edge 3000 stall converter.
Built transmission (got it from YenkoST from this board, he had it in a pickup that was around 400+hp)
Good bosch maf
An extra iac valve
A set (front and rear) of never installed kyb gr2 shock/struts.
a new ac delco fuel pump.
A "small" distributor with around 2000 miles on our.
Flow tech headers
The Roller that needs paint and a new rear spoiler so bad.
A water pump and starter with less than 500 miles. (Cheap autozone)
2 sets of valve covers, one tall from summit (chrome), and the stockers.
A msd coil
New ( installed and ran for an hour) set of plugs and ignition wires.
The wiring harness from an 89 formula 350 (some cuts/splices)
Stock intake tubing
ac system is inop, but there is an ac delco blower motor with 500 miles on it.
The block, bought from a guy here bored to .030...... If it is viable.
Speed pro pistons, if they are viable
Stock crank and rods, if viable.
Misc interior bits. Good dash pad.
If you are interested pm me.
Based on interest, I'll update this with prices and all the pertinent info.
#3
Junior Member
Join Date: Jan 2007
Location: Houston Tx
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Iroc-Z28
Engine: TBI 305 Bored 30 over mild Mods
Transmission: 700R4
Axle/Gears: Stock
Re: debating a part out situation. fishing for interest.
Price on blower motor, And fuel pump got the part # of it..
#4
Junior Member
iTrader: (1)
Join Date: May 2012
Location: Wisconsin
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Iroc-Z
Engine: 350 TPI
Transmission: 700R4
Re: debating a part out situation. fishing for interest.
Price on stealth ram, complete.
&
Profiler 185cc/64cc heads. Hydro springs from profiler good for .650 lift. 2.02 / 1.6 valves.
&
Profiler 185cc/64cc heads. Hydro springs from profiler good for .650 lift. 2.02 / 1.6 valves.
#5
Member
Join Date: Oct 2000
Location: amanda ,ohio,usa
Posts: 128
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 camaro
Engine: 355 tpi
Transmission: 700r
Axle/Gears: 3.50
Re: debating a part out situation. fishing for interest.
stealthram late version so it can port to 1206? is it ported already? price?
#6
Member
Thread Starter
iTrader: (2)
Join Date: Jun 2006
Location: Rocky Face, Ga
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Formula
Engine: 355ci HSR SBC
Transmission: 700r4
Axle/Gears: 3.27
Re: debating a part out situation. fishing for interest.
I'm just getting interested parties now..... part out is dependent on cost of repair. If it is cost prohibitive to repair, I'm going to part it out. I'll know by Monday or Tuesday.
I believe the SR is the old style. It is still on the car. 600+ shipping. Add 100 for fuel pressure gauge and braided lines.
#7
Member
Re: debating a part out situation. fishing for interest.
interested in the cam and the HSR (lines as FPR and Lines as well)
Trending Topics
#13
Supreme Member
iTrader: (1)
Join Date: May 2015
Location: Temecula, CA
Posts: 1,149
Received 83 Likes
on
67 Posts
Car: 1989 Pontiac Formula 350
Engine: L98
Transmission: 700R4
Axle/Gears: BorgWarner 3.27 Posi
Re: debating a part out situation. fishing for interest.
Highly interested in dash pad. PM me pics and price pls
Grey interior? post up pics - need a ton of 89 formula stuff.
Grey interior? post up pics - need a ton of 89 formula stuff.
#16
Senior Member
iTrader: (5)
Join Date: Feb 2005
Location: meridian, idaho
Posts: 691
Likes: 0
Received 0 Likes
on
0 Posts
Car: 92 1500p\u 2wd
Engine: 91 z28 tpi 355
Transmission: 91 700r4
Re: debating a part out situation. fishing for interest.
If the stealthram in the new 2006+ one I'd be interesred
#17
TGO Supporter/Moderator
iTrader: (12)
Join Date: Jul 1999
Location: SALEM, NH
Posts: 11,735
Likes: 0
Received 89 Likes
on
75 Posts
Car: '88 Formula, '94 Corvette, '95 Bird
Engine: LC9, 355" LT1, LT1
Transmission: T5, Zf6, 4L60E
Axle/Gears: 3.42, Dana44 3.45, 3.23
Re: debating a part out situation. fishing for interest.
How much are the heads?
-- Joe
-- Joe
Thread
Thread Starter
Forum
Replies
Last Post
Street Lethal
Power Adders
634
04-30-2019 12:14 PM
LT1Formula
Engine/Drivetrain/Suspension Parts for Sale
20
11-14-2015 12:02 AM