[PA] WTB Spohn crossmember for T-56
10-06-2013, 08:28 PM
#1
Senior Member
Thread Starter
iTrader: (3)
Join Date: Jul 1999
Location: Mechanicsburg, PA
Posts: 816
Likes: 0
Received 0 Likes
on
0 Posts
Car: '89 Formula 350
Engine: 5.7L L98 TPI
Transmission: 700-R4 Automatic
Axle/Gears: 7.5 disc posi 3.23
WTB Spohn crossmember for T-56
Need the crossmember to adapt in an LT-1 t56 into a thirdgen. Can be with or without driveshaft loop. Preferably without torque arm mount but will take either.
Let me know what you got.
Let me know what you got.
10-07-2013, 08:27 AM
#2
Junior Member
Join Date: Jun 2007
Location: Waukesha, WI
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Car: Cameron (The Camaro)
Engine: SBC 385 Stroker
Transmission: Stage 2+ T56 Six Speed
Axle/Gears: 3.42 Richmond Gear Locked Posi
Re: WTB Spohn crossmember for T-56
Just a heads up, if you plan on ever running long tubes on the car don't go with that crossmember, it hangs too low and will inevitably cause a ton of clearance issues that are more or less unfixable. Hawks makes a nice "m" shaped crossmember thats affordable and tucks up really nice. The Spohn one literally hangs down 3" lower than stock.
10-07-2013, 09:00 AM
#3
Senior Member
Thread Starter
iTrader: (3)
Join Date: Jul 1999
Location: Mechanicsburg, PA
Posts: 816
Likes: 0
Received 0 Likes
on
0 Posts
Car: '89 Formula 350
Engine: 5.7L L98 TPI
Transmission: 700-R4 Automatic
Axle/Gears: 7.5 disc posi 3.23
Re: WTB Spohn crossmember for T-56
Awesome. Thanks. I'll check it out.
10-07-2013, 09:43 AM
#4
Junior Member
Join Date: Jun 2007
Location: Waukesha, WI
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Car: Cameron (The Camaro)
Engine: SBC 385 Stroker
Transmission: Stage 2+ T56 Six Speed
Axle/Gears: 3.42 Richmond Gear Locked Posi
Re: WTB Spohn crossmember for T-56
http://www.hawksthirdgenparts.com/pr...6-6-Speed.html
here's the one that works with long tubes, I have the same one on my car running hooker super comp longtubes to a mufflex y-pipe, I couldn't ask for more clearance and I have a 4" intermediate pipe! Good luck
here's the one that works with long tubes, I have the same one on my car running hooker super comp longtubes to a mufflex y-pipe, I couldn't ask for more clearance and I have a 4" intermediate pipe! Good luck
10-07-2013, 09:51 AM
#5
Senior Member
Thread Starter
iTrader: (3)
Join Date: Jul 1999
Location: Mechanicsburg, PA
Posts: 816
Likes: 0
Received 0 Likes
on
0 Posts
Car: '89 Formula 350
Engine: 5.7L L98 TPI
Transmission: 700-R4 Automatic
Axle/Gears: 7.5 disc posi 3.23
Re: WTB Spohn crossmember for T-56
Looks great and it's cheaper too. I didn't think about exhaust clearance so this should work out wonderful. Thanks a lot I'll be on the lookout for one of these.
10-07-2013, 10:43 AM
#6
Junior Member
Join Date: Jun 2007
Location: Waukesha, WI
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Car: Cameron (The Camaro)
Engine: SBC 385 Stroker
Transmission: Stage 2+ T56 Six Speed
Axle/Gears: 3.42 Richmond Gear Locked Posi
Re: WTB Spohn crossmember for T-56
Yeah I had the whole spohn setup with the torque arm for my car, quality construction but impractical design, sold that setup and ended up going with a Hawks Sinister torque arm with a cross brace instead
Thread
Thread Starter
Forum
Replies
Last Post
TinnMann2
Canadian Region
16
06-18-2017 05:10 PM
kammi10
Engine/Drivetrain/Suspension Parts for Sale
2
11-09-2015 08:28 PM
darwinprice
Organized Drag Racing and Autocross
17
10-11-2015 11:51 PM
tonys91rs
Engine/Drivetrain/Suspension Parts for Sale
3
10-10-2015 03:31 PM
tmork454
Transmissions and Drivetrain
0
09-29-2015 06:33 PM