[IL] WTB Bell Housing for V8 T5 Hydraulic
#1
Junior Member
Thread Starter
Join Date: Nov 2013
Location: Flanagan, Illinois
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1983 Trans Am
Engine: Chevy 350
WTB Bell Housing for V8 T5 Hydraulic
In need of a bell housing for anything from 84-92 for a hydraulic clutch swap. Needs be for the v8 t5 and have the slave cylinder mount.
#2
Supreme Member
iTrader: (13)
Join Date: Dec 2002
Location: Bowdon, GA.
Posts: 2,535
Likes: 0
Received 16 Likes
on
14 Posts
Car: 1988 Camaro
Engine: 355, 10.34:1, 249/252 @.050", IK200
Transmission: TH-400, 3500 stall 9.5" converter
Axle/Gears: Ford 9", detroit locker, 3.89 gears
Re: WTB Bell Housing for V8 T5 Hydraulic
I may have you one tomorrow. I'm picking up an 85 that I will be parting out and it has a T5.
I will let you know about this time tomorrow night if it has a good bell or not
I will let you know about this time tomorrow night if it has a good bell or not
#3
Junior Member
Thread Starter
Join Date: Nov 2013
Location: Flanagan, Illinois
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1983 Trans Am
Engine: Chevy 350
Re: WTB Bell Housing for V8 T5 Hydraulic
Great! Looking forward to the result. Junkyards around here are barren as far as manuals.
#5
Junior Member
Thread Starter
Join Date: Nov 2013
Location: Flanagan, Illinois
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1983 Trans Am
Engine: Chevy 350
Re: WTB Bell Housing for V8 T5 Hydraulic
Ouch, that's a big chunk. If it were just the crack I wouldn't be worried and just weld it up. But I couldn't do much about a whole piece knocked out. I don't have a lot of knowledge on this but in your opinion, would that chip be a structural problem for the rest of the housing? Usually I'd probably be dumb enough not to question it and just run with it.
#6
Supreme Member
iTrader: (13)
Join Date: Dec 2002
Location: Bowdon, GA.
Posts: 2,535
Likes: 0
Received 16 Likes
on
14 Posts
Car: 1988 Camaro
Engine: 355, 10.34:1, 249/252 @.050", IK200
Transmission: TH-400, 3500 stall 9.5" converter
Axle/Gears: Ford 9", detroit locker, 3.89 gears
Re: WTB Bell Housing for V8 T5 Hydraulic
I'm kind of like you. I'm not really sure. If it was me, I would try it. Maybe drill the end of the crack to keep it from spreading and weld the crack and maybe weld a brace (flat stock) across where the chunk is missing and give it a go.
I really hate that it's broke, I thought I was going to have you a good one.
If interested make me an offer. Not sure what shipping will be but shoot me your zip and I will find out tomorrow
I really hate that it's broke, I thought I was going to have you a good one.
If interested make me an offer. Not sure what shipping will be but shoot me your zip and I will find out tomorrow
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
Shaneo
Transmissions and Drivetrain
7
09-01-2002 12:57 PM