Misc. Parts for 1988 Camaro IROC
#1
Senior Member
Thread Starter
Join Date: Jun 2011
Location: Melbourne, Australia
Posts: 839
Likes: 0
Received 1 Like
on
1 Post
Car: 1988 IROC Camaro (RHD)
Engine: 350 ci L98 SBC
Transmission: T700
Axle/Gears: 9 bolt BW, Disk, Posi-traction
Misc. Parts for 1988 Camaro IROC
Hi,
I have a 1988 IROC and am looking for these parts:
1) Right/passenger inner fender large curved black plastic skirt
2) Right/passenger rectangular black plastic piece that fits horizontally under the front bumper, it's about 20cm * 30cm in size.
3) Right/passenger B pillar black plastic trim piece about 1 ft long that fits vertically over the weather seal.
4) Left/driver side lower ground effect bracket. Only need the metal bracket. It has two holes that screw into the ground effect and a stud that mounts to the body with a speed nut.
5) Pair of sunvisor brackets
6) Headliner or headliner board. Already have the material, just need the board to use as a template.
I'm in Melbourne Australia, but can use a shipping agent in Portland 97203.
Thanks
Peter
I have a 1988 IROC and am looking for these parts:
1) Right/passenger inner fender large curved black plastic skirt
2) Right/passenger rectangular black plastic piece that fits horizontally under the front bumper, it's about 20cm * 30cm in size.
3) Right/passenger B pillar black plastic trim piece about 1 ft long that fits vertically over the weather seal.
4) Left/driver side lower ground effect bracket. Only need the metal bracket. It has two holes that screw into the ground effect and a stud that mounts to the body with a speed nut.
5) Pair of sunvisor brackets
6) Headliner or headliner board. Already have the material, just need the board to use as a template.
I'm in Melbourne Australia, but can use a shipping agent in Portland 97203.
Thanks
Peter
Last edited by peterc005; 01-24-2017 at 11:53 PM.
#2
Supreme Member
iTrader: (128)
Join Date: Aug 2009
Location: Central California
Posts: 1,821
Likes: 0
Received 37 Likes
on
34 Posts
Car: 92 Camaro RS
Engine: LO3
Transmission: T5
Axle/Gears: stock
Re: Misc. Parts for 1988 Camaro IROC
If you have a junk yard anywhere, those sun visor brackets were used on lots of GM cars of similar vintage. Many were chrome instead of black but work the same and likely paintable
#3
Senior Member
Thread Starter
Join Date: Jun 2011
Location: Melbourne, Australia
Posts: 839
Likes: 0
Received 1 Like
on
1 Post
Car: 1988 IROC Camaro (RHD)
Engine: 350 ci L98 SBC
Transmission: T700
Axle/Gears: 9 bolt BW, Disk, Posi-traction
Re: Misc. Parts for 1988 Camaro IROC
Thanks for the tip.
I might buy a new pair of sun visor brackets from Hawks use some second hand ones pop up.
Here in Australia third gens are rare and it's hard to find parts.
When the car was converted to right hand drive the original sun visors were replaced with padded ones for registration compliance. These padded sin visors were a different colour and only had two screws, so I'm looking to get back to original.
I might buy a new pair of sun visor brackets from Hawks use some second hand ones pop up.
Here in Australia third gens are rare and it's hard to find parts.
When the car was converted to right hand drive the original sun visors were replaced with padded ones for registration compliance. These padded sin visors were a different colour and only had two screws, so I'm looking to get back to original.
#6
Member
Re: Misc. Parts for 1988 Camaro IROC
I think I have the b pillar trim. I'll double check when I get back in the garage.
#7
Senior Member
Thread Starter
Join Date: Jun 2011
Location: Melbourne, Australia
Posts: 839
Likes: 0
Received 1 Like
on
1 Post
Car: 1988 IROC Camaro (RHD)
Engine: 350 ci L98 SBC
Transmission: T700
Axle/Gears: 9 bolt BW, Disk, Posi-traction
Re: Misc. Parts for 1988 Camaro IROC
Thanks, no big drama about the B pillar trim. I seem to have lost it after the body strip and paint, it'll probably turn up after I buy another one!
Also looking for some rear PBR calipers and cables if you have any?
Also looking for some rear PBR calipers and cables if you have any?
Trending Topics
#8
Member
Re: Misc. Parts for 1988 Camaro IROC
b pillar and the fender plastics. fender plastics need a good cleaning.
#9
Senior Member
Thread Starter
Join Date: Jun 2011
Location: Melbourne, Australia
Posts: 839
Likes: 0
Received 1 Like
on
1 Post
Car: 1988 IROC Camaro (RHD)
Engine: 350 ci L98 SBC
Transmission: T700
Axle/Gears: 9 bolt BW, Disk, Posi-traction
Re: Misc. Parts for 1988 Camaro IROC
The quarantine border security people here get funny about second hand parts, so it would be great if you could hose off any loose dirt. Grease and grime don't matter, just loose dirt.
I've got C &C T Tops and those B pillar trims are different. Looks like I'll have to keep looking. The missing piece must be in the workshop somewhere, I just can't find it!
Please PM me a price including shipping and your Paypal details.
Thanks
Peter
I've got C &C T Tops and those B pillar trims are different. Looks like I'll have to keep looking. The missing piece must be in the workshop somewhere, I just can't find it!
Please PM me a price including shipping and your Paypal details.
Thanks
Peter
#12
Senior Member
Thread Starter
Join Date: Jun 2011
Location: Melbourne, Australia
Posts: 839
Likes: 0
Received 1 Like
on
1 Post
Car: 1988 IROC Camaro (RHD)
Engine: 350 ci L98 SBC
Transmission: T700
Axle/Gears: 9 bolt BW, Disk, Posi-traction
Re: Misc. Parts for 1988 Camaro IROC
Still searching if anyone is wrecking a Camaro?