91-92 Firehawk flywheel and clutch questions?
#1
Member
Thread Starter
iTrader: (3)
Join Date: May 2004
Location: NY
Posts: 264
Likes: 0
Received 2 Likes
on
2 Posts
Car: Currently Looking
Engine: Five Seven
Transmission: 700R4
Axle/Gears: 3.27
91-92 Firehawk flywheel and clutch questions?
I was wondering, the original 25 Firehawks used the ZF 6-speed out of the C4 Corvettes and had a special bellhousing made up to be able to fit them into the F-body. Does anybody know if the Firehawks also used the same dual mass flywheel and clutch combination? Or was their clutch setup also custom?
#2
Supreme Member
iTrader: (8)
Join Date: Oct 2001
Location: Il
Posts: 11,731
Received 782 Likes
on
527 Posts
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: 91-92 Firehawk flywheel and clutch questions?
The firehawk has its own bellhousing.
From what I have taken pix of, seen and remember the base hawks used the factory Fbody 1piece seal flywheel clutch disc, pressure plate, throwout bearing, fork and hydraulics.
The aluminum 2 piece seal motor cars used a dif flywheel from a 85? T5 setup?
It also uses its own stamped steel trans Xmember. But a 89 TTA part will work.
From what I have taken pix of, seen and remember the base hawks used the factory Fbody 1piece seal flywheel clutch disc, pressure plate, throwout bearing, fork and hydraulics.
The aluminum 2 piece seal motor cars used a dif flywheel from a 85? T5 setup?
It also uses its own stamped steel trans Xmember. But a 89 TTA part will work.
Last edited by TTOP350; 01-20-2017 at 12:23 PM.
#3
Re: 91-92 Firehawk flywheel and clutch questions?
The firehawk has its own bellhousing.
From what I have taken pix of, seen and remember the base hawks used the factory Fbody 1piece seal clutch,disk, pressure plate, throwout bearing, fork and hydraulics.
The aluminum 2 piece seal motor cars used a dif flywheel from a 85? T5 setup?
It also uses its own stamped steel trans Xmember. But a 89 TTA part will work.
From what I have taken pix of, seen and remember the base hawks used the factory Fbody 1piece seal clutch,disk, pressure plate, throwout bearing, fork and hydraulics.
The aluminum 2 piece seal motor cars used a dif flywheel from a 85? T5 setup?
It also uses its own stamped steel trans Xmember. But a 89 TTA part will work.
#4
Supreme Member
iTrader: (8)
Join Date: Oct 2001
Location: Il
Posts: 11,731
Received 782 Likes
on
527 Posts
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: 91-92 Firehawk flywheel and clutch questions?
I'll have to see if it still uses the late model GM spline disc.
Thread
Thread Starter
Forum
Replies
Last Post
BlackphantomZ28
Engine/Drivetrain/Suspension Parts for Sale
4
04-24-2016 08:14 AM