cprmn14

iTrader: (3)

Ok that's fine, thanks kris

Pocket

iTrader: (24)

Tee it into a coolant line somewhere. Its supposed to be the highest point in the system, but several have gotten by putting it anywhere

zraffz

Your car is beautiful dude!

cprmn14

iTrader: (3)

Ok pocket ill see what I can do.

Thanks a lot zraffz!
I appreciate it!

9014josh

iTrader: (1)

my steam tube is not even hooked up lol its all capped off,drove it all summer though and never had any heating problems.

cprmn14

iTrader: (3)

Today I messed around with the motor alittle more. I realized that the steel threaded plugs in the back of the cylinder head will not come out. So I'm just going to take pockets advice and "T" it into another coolant line. I was thinking maybe the line coming off the heater core to the waterpump. Unless there is a better way.

On another note I took out the #3 fitting on the waterpump to the oil cooler, and I'm blocking it off with a 1\2" freeze plug. So after the pilot bushing and mounts this motor should be ready to drop in!!!! Starting to get excited!!!

quickkris2006

iTrader: (2)

yea i cant get mine off either! its rather annoying.. if it wont hurt to block them off i wouldnt mind doing it as well.. i havent had anytime to work on mine.. got court tomorrow...

cprmn14

iTrader: (3)

Blocking it off was easy, just got a threaded plug from the hardware store and some locktite. But the only reason I had to block it off was because I switched up the heads after I put my headgasket on, so the threads were in the front. And yeah those plugs are in there pretty good.

cprmn14

iTrader: (3)

well I've been doing some reading and I think I might have messed up on the bypass. I have plugs in all 4 corners of the heads, and was going to run the bypass it at the throttle body, but I guess that causes hot spots in the heads, which they say is a problem with 4th gen heads. But I've heard of a couple people who have blocked it off completely and had no problems, but I don't know if its worth the risk.

Any suggestions, or anyone ever ran this set up?

quickkris2006

iTrader: (2)

so u accidently put the heads on the wrong sides of the motor? that sucks lol

cprmn14

iTrader: (3)

Yeah I know right, lol must have been spacing out. But its no big deal, I got the threaded plugs out tonight so I can reinstall the steam line in the stock location. (Thank god)

cprmn14

iTrader: (3)

Today I just painted my SBC mounts and mounted the clam shell to my LT1. One question, where you put the clam shell on the pass. Side of the motor there was a random bracket. Should it be relocated or just forgot about. I have a pic


Other than that progress has been slow. Snow makes money slow, but hopefully ordering poly mounts soon and a pilot bushing so I can fit the motor in her new home

quickkris2006

iTrader: (2)

if snow makes ur money slow how are u not broke lol jk looking good tho.. ill have to look at mine to see if i have that bracket.. now how did u get the threaded plugs out mine wont budge!!

cprmn14

iTrader: (3)

I took a propane torch and heated up the area around the bolt. I just heated it for a minute and it broke free right away. And yeah I do construction and we work around the snow, so it puts a slow on hours, lol.

I just ordered my poly mounts today too!

quickkris2006

iTrader: (2)

yea i know what u mean about the construction.. my dads been doing it for over 30 years now.. ive been on sites my whole life.. i do roofing and pour foundations in the summer.. good money hard work.. and get a really nice tan at the same time lol

cprmn14

iTrader: (3)

Just alittle update, I got my prothane mounts in the mail and in the clamshells, probably
Going to slap them in today, then the next step is getting to motor in!

cprmn14

iTrader: (3)

Got the mounts installed on the kmember



Now all I have to do is install a pilot bushing and replace a sensor and the motor can go in!

quickkris2006

iTrader: (2)

and clean that idler arm and paint it!! easyest to do it now lol ur farther along then me .. i took a huge step back.. never thought i would get rid of my vert but couldnt pass up that ta..

Jeromey Cummins

iTrader: (5)

subscribed

cprmn14

iTrader: (3)

Big update: THE MOTOR IS IN! . And sure does look at home.


I'm really stoked, it fell right into place. I don't have the trans yet, and probably won't for a few
Months so I installed the pilot bushing and dropped it in. That way I can start on fuel lines and powersteering, etc etc.

Question: can I reuse the flywheel out of an automatic in a 6 speed?

92droptopws6

iTrader: (10)

Great looking project.

IROC-Z28_CAMARO

iTrader: (4)

Auto does not use a flywheel, they use a flexplate. You will need to find a flywheel.

Josh

quickkris2006

iTrader: (2)

nice!!!!!

cprmn14

iTrader: (3)

Thanks man. I was surprised it fell right into place on the new poly mounts. Now I've just got to start installing everything.

cprmn14

iTrader: (3)

Today I got a few things done after work, got the rear end out, so the fuel tank comes next. Then removing the fuel lines( since the fitting was seized, I cut the line) so I'm going to replace them with napa steel lines connected to pure choice braided lines.

Here's a pic of the rear end finally all disconnected

cprmn14

iTrader: (3)

Also today I bolted in the power steering pump, and started with the lines. I was alittle nervous because I didn't want to kink the line, but I forgot that I bought the pump/lines/reservoir from a guy who was parting out an LT1 swapped third gen trans am. So the line from the pump seems to be a perfect fit. But as for the reservoir, I'm not sure where I'm going to mount it. I'd like to mount it on the motor if possible but I don't mind mounting it elsewhere, if need be.

Here's a pic of the line from the pump, it seems alittle long, but should work fine. Let me know what you think.

quickkris2006

iTrader: (2)

did u have to mod one of ur motor mounts? ive heard that u had to but wondering if u did? im hoping to drop my motor in on saturday

cprmn14

iTrader: (3)

None what so ever. Just make sure you don't mix them up when you put them in, I've heard of people doing that. And I used my 305 clamshells on the LTx also. Can't wait to see your motor dropped in and good luck!

cprmn14

iTrader: (3)

4th gen seats modified and installed. Picked the up out of a 96 V6 camaro in a scrap yard for 40$. Pretty good find.

cprmn14

iTrader: (3)

Today was a stressful day, got the fuel tank out (PITA!!) And removed the sender and installed my walbro fuel pump. When removing the sender a few pieces of dirt fell off the sender lines so ill have to clean the tank with some kind of solvent. But with the new pump, they sent a plug and play type harness that plugs in my old fuel pump. But there's a lot of loose wires, should I cut and solder the wires, or is that ok?


Also, I realized I don't have a parking brake actuator on my rear end. Do i have to install a whole new ebrake system or just get a new actuator?

-Cooper

cprmn14

iTrader: (3)

Today I reinstalled the fuel tank, and removed the old steel lines. Replacing them and getting braided lines from Purechoice from the intake to the back of the firewall, to the steel lines.

I also installed my other power steering line which required no modification. Just need to decide where to mount my reservoir.

But I still can't figure out my ebrake. Do I just install an actuator, or am I missing a lot? Anyone else have this problem?

quickkris2006

iTrader: (2)

Any updates??

blue_thunder91

Very nice work! I am starting my lt1 swap into a 91 z28 and I'm curious, what are you doing about ur wiring harness? Are you ordering from painless or having someone retrofit its?

cprmn14

iTrader: (3)

not any updates to report.(trying to save up to get my 1980 yamaha 1100 fixed) just got my UMI adjustable panhard bar in the mail, and my pinion seal from NAPA. Sorry you have to leave soon man, your swap was coming along very well.

Congrats on the swap, way to keep the LTx family alive!As for my harness, im saving myself the massive headache and sending my harnesses to Pocket to have them mated. and i would recommend reading ALL of the stickies and collect as many parts as you can before you begin. you dont want to be like me and being held up by it.

blue_thunder91

Well I have pretty much all I will need except for my wire harness and A/C Lines. Do u have contact info for pocket? And what's the price for it

cprmn14

iTrader: (3)

Today I got my pinion seal replaced, It was leaking pretty bad. And got the rear end all bolted in.

Pic of the old seal

cprmn14

iTrader: (3)

And the new

quickkris2006

iTrader: (2)

damn u got that thing really clean.. ever think about cleaning the whole rear and painting it? and i have those same jackstands lol

cprmn14

iTrader: (3)

Actually I cleaned and painted it last winter, Shows how fast it can get dirty. Plus sand blasting it was a PITA! So I just threw it in there as is.

dprest68

iTrader: (1)

I'm right there with you on that. Having just prepped and painted the rearend for my car, I wouldn't want to have to do it twice either. It barely gets seen anyways. Your swap looks like it's coming along nicely. And I like your 4th gen seats. They look really nice!

cprmn14

iTrader: (3)

Thanks man, I was really excited to snag those seats. And funny thing is I didn't even plan on getting them, I stumbled across them on my way OUT of the pick-and-pull. Your swaps coming along very good aswell.

Blue_thunder- you can find him under practically every swap. Just shoot him a pm and let him know what your working with as far as emissions, trans, and anything you deleted. He'll give you an accurate estimate.

cprmn14

iTrader: (3)

I've been doing research, and I still can't find a good thread about a 4th gen parking brake switch. Is that all I'm missing or am I missing ebrake pads? Any one else have a solution?

Thanks!

cprmn14

iTrader: (3)

Today I finish tightening down my sway bar and my UMI panhard bar, and got the rear end on the ground. It kind of feels like a check point has been reached, ha.
Anyway I'm ordering fuel lines from Pure Choice tomorrow, and I'm turning 21 on Saturday so maybe ill be looking at some birthday money for more parts!

Here's a pic of the adj. panhard bar, looks right at home with the Hotchkis sway bar.

dprest68

iTrader: (1)

Happy Birthday!

cprmn14

iTrader: (3)

Thanks man!

quickkris2006

iTrader: (2)

happy bday man!! dont get to drunk!!!!

cprmn14

iTrader: (3)

Thanks kris! All I can say is, you only turn 21 once...

-Cheers!

cprmn14

iTrader: (3)

What do you guys think about these headers? Their Hooker Competition Shorties, 1 5\8 primarys, but it says oval ports, not D ports. If that makes a diffrence.

Anyone running these on their LT1?

quickkris2006

iTrader: (2)

screw the shorties they are a WASTE OF MONEY!! get long tubes and do it the right way! lol .. shoot for right now im goin no headers lol i leave monday so im not worried about it lol

cprmn14

iTrader: (3)

Yeah I want to go long tube, but I don't want to get a custom y-pipe fabricated since all the exhaust shops want to dollar for custom pieces. And ground clearance I've heard is an issue with cheap long tubes. But I haven't decided yet, open to opinions!

But I should get my Purechoice braided lines in the mail today, so more pics and updates on that hopefully tomorrow