350 4 bolt main engine, MINT 90-92 auto shifter plate camaro
#1
Junior Member
Thread Starter
Join Date: Sep 2004
Location: Shelby, North Carolina
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 IROC Z
Engine: 350 tuned port injection
Transmission: t-56 6 speed
350 4 bolt main engine, MINT 90-92 auto shifter plate camaro
the 350 runs great and has a serpintine setup on it, compressor and all. it has some wild *** cam in it that *** only knows what lift it is. if i remember right it is a .555 lift cam with a lot of duration. any way it was in there when i got the car. its a ground pounder and does great above 2000 rpm with a 750cfm carb. i will take $400 for it if you come and get it.
I have a 90-92 auto shifter plate from a 1990 IROC with 84,000 original miles on it, looks brand new without anyflaws and has the yellow lettering on it. $65 shipped
i am in shelby, nc 28073
thanks
Barry
I have a 90-92 auto shifter plate from a 1990 IROC with 84,000 original miles on it, looks brand new without anyflaws and has the yellow lettering on it. $65 shipped
i am in shelby, nc 28073
thanks
Barry
Last edited by ManWitThePlan; 03-04-2005 at 02:06 AM.
#2
Junior Member
Thread Starter
Join Date: Sep 2004
Location: Shelby, North Carolina
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 IROC Z
Engine: 350 tuned port injection
Transmission: t-56 6 speed
i would trade that 350 for a good 3.1 or 3.4 and a good wiring harness for a manual camaro.
Last edited by ManWitThePlan; 03-04-2005 at 02:05 AM.
#4
Junior Member
Thread Starter
Join Date: Sep 2004
Location: Shelby, North Carolina
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 IROC Z
Engine: 350 tuned port injection
Transmission: t-56 6 speed
whats your email??? it tells me that they are too large to post here?? o well i will send them to you later today if i get your email in time.
thanks
Barry
thanks
Barry
#5
Member
Join Date: Nov 2003
Location: Detroit, MI
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Pontiac Trans Am GTA
Engine: L98 350
Transmission: 700R4
Do you know anything about the shortblock assembly? heads? ect.
I may in the market for a long block...let me know.
Thanks
Ryan
I may in the market for a long block...let me know.
Thanks
Ryan
#6
Junior Member
Thread Starter
Join Date: Sep 2004
Location: Shelby, North Carolina
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 IROC Z
Engine: 350 tuned port injection
Transmission: t-56 6 speed
here are the casting numbers from the heads and block, also have an extra set of heads to go with it.
10036033...350...........4...Goodwrench crate motor, 2-piece rear
seal
3998993....current..350.........Goodwrench crate motors,75cc chambers
extra heads
333882.....74-80...350/400......76cc chambers
10036033...350...........4...Goodwrench crate motor, 2-piece rear
seal
3998993....current..350.........Goodwrench crate motors,75cc chambers
extra heads
333882.....74-80...350/400......76cc chambers
Thread
Thread Starter
Forum
Replies
Last Post
84z96L31vortec
Tech / General Engine
7
08-20-2017 12:16 AM
84z96L31vortec
North East Region
1
08-10-2015 08:27 PM