Trick Flow Heads for Small Chevy (Twisted Wedge)
#1
Junior Member
Thread Starter
Join Date: Feb 2005
Location: Liberty Hill T.X.
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Car: 73' Nova~~~TPI Powered
Engine: 283 Cubic Inch Rev MUNSTER!!
Transmission: Turbo 350
Axle/Gears: GM10 bolt w/4.56 posi
Trick Flow Heads for Small Chevy (Twisted Wedge)
Hey guys, I have a very nice set of heads for sale. I just picked them up at the local machine shop. I had some big plans for these heads, but right after the day I purchased them, I ran accross a super deal on a complete 94 Z-28 with a LT1/4L60E drivetrain. Obviously these heads will not work on the LT!.....so, now they need to go.
These are a great set of Trick flow small block chevy cylinder heads-they have just been machined and ported at www.PortPros.com. No run time at all since the modifications. Heads were on an engine for about a month before they were reworked. They have Manly stainless steel swirl polished intake and exhaust valves. 2.020 IN and 1.600 EX. They are machined with a 5-angle valve job-bronze guide liners-new valve seals-the decks have been milled just enough to give a perfect finish for great gasket sealing.They have brand new comp cams springs-chrome moly retainers-chrome moly spring seat locators and locks. These head have canted valves and will support 500HP. These are a great set of heads for the street or strip. These heads will not disappoint. Heads have been CC'd at 63cc chambers and 205cc intake runners. Heads have 7/16" threadded holes for your screw in studs for the rockers.
These heads are for the GenI style motors with the old style (pre 86) intake manifold bolt holes. They can be used on a TPI or TBI engine with a little modification to your intake.
Asking $1000 plus shipping. Need to get them gone!
If you have any questions, please shoot me a PM.
Thanks!
Joe Hopkins
These are a great set of Trick flow small block chevy cylinder heads-they have just been machined and ported at www.PortPros.com. No run time at all since the modifications. Heads were on an engine for about a month before they were reworked. They have Manly stainless steel swirl polished intake and exhaust valves. 2.020 IN and 1.600 EX. They are machined with a 5-angle valve job-bronze guide liners-new valve seals-the decks have been milled just enough to give a perfect finish for great gasket sealing.They have brand new comp cams springs-chrome moly retainers-chrome moly spring seat locators and locks. These head have canted valves and will support 500HP. These are a great set of heads for the street or strip. These heads will not disappoint. Heads have been CC'd at 63cc chambers and 205cc intake runners. Heads have 7/16" threadded holes for your screw in studs for the rockers.
These heads are for the GenI style motors with the old style (pre 86) intake manifold bolt holes. They can be used on a TPI or TBI engine with a little modification to your intake.
Asking $1000 plus shipping. Need to get them gone!
If you have any questions, please shoot me a PM.
Thanks!
Joe Hopkins
Last edited by kokamo; 11-09-2006 at 05:01 PM. Reason: Price change.
#3
Junior Member
Thread Starter
Join Date: Feb 2005
Location: Liberty Hill T.X.
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Car: 73' Nova~~~TPI Powered
Engine: 283 Cubic Inch Rev MUNSTER!!
Transmission: Turbo 350
Axle/Gears: GM10 bolt w/4.56 posi
They are the G1 heads witch have the 13* intake / 23* exhaust valve.
Forgot to mention that, sorry!
Joe
Forgot to mention that, sorry!
Joe
#4
Junior Member
Thread Starter
Join Date: Feb 2005
Location: Liberty Hill T.X.
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Car: 73' Nova~~~TPI Powered
Engine: 283 Cubic Inch Rev MUNSTER!!
Transmission: Turbo 350
Axle/Gears: GM10 bolt w/4.56 posi
PRICE CHANGE!!!
Will take $1000 for these heads! Need to get them gone!
Thread
Thread Starter
Forum
Replies
Last Post
Mickeyruder
Engine/Drivetrain/Suspension Parts for Sale
3
09-02-2015 02:45 PM