Mike almost finished
02-07-2005, 11:45 PM
#1
Supreme Member
Thread Starter
Join Date: Dec 2001
Posts: 1,411
Likes: 0
Received 0 Likes
on
0 Posts
Mike almost finished
I pretty much have it all polished out.. I need now to get a new grinder buffing wheel for rougue, gold sterling etc.. And Shine it up the rest of the way, this has been by hand.. I need to get a wheel on my Sr Plenum to get it all shined back up..
Last edited by BrandenCali; 06-09-2006 at 10:38 PM.
02-08-2005, 04:20 PM
#6
Supreme Member
Thread Starter
Join Date: Dec 2001
Posts: 1,411
Likes: 0
Received 0 Likes
on
0 Posts
haha.. Ok that picture did not do justice.. But I can get the drive shaft pretty Nice.. Once I buy the new polishing wheel and the stuff to rougue..
Once I have all my polishing tools.. I can polish out driveshaft's that are in well condition.. This one I have hear I bought from Red Rocket, It was near Brand New..
When the heads come off.. I will have time to Polish out my Plenum on The Super Ram.. Gene says it should Shine like the lid it used to.. So I seen what I can do with the drive shaft.. I know the next Time You see SR it will be looking much better.. Gene has a few other chrome Pieces I need to get.. I'll have some Steel Braided Line's on most hoses that have fluids..
Randy.. Im sure it would take some time to get a Base Polished out.. You would have to spend all the time smoothing everything Down.. How about Polish out your SR.. I know if all goes well with my Polishing Im going to do My Runner's..
Once I have all my polishing tools.. I can polish out driveshaft's that are in well condition.. This one I have hear I bought from Red Rocket, It was near Brand New..
When the heads come off.. I will have time to Polish out my Plenum on The Super Ram.. Gene says it should Shine like the lid it used to.. So I seen what I can do with the drive shaft.. I know the next Time You see SR it will be looking much better.. Gene has a few other chrome Pieces I need to get.. I'll have some Steel Braided Line's on most hoses that have fluids..
Randy.. Im sure it would take some time to get a Base Polished out.. You would have to spend all the time smoothing everything Down.. How about Polish out your SR.. I know if all goes well with my Polishing Im going to do My Runner's..
Trending Topics
02-08-2005, 04:47 PM
#8
Member
Join Date: Jan 2005
Location: Huntington Beach
Posts: 171
Likes: 0
Received 0 Likes
on
0 Posts
Car: F-Bodys
Engine: 355
Transmission: shifting
Hey brandon that looks good but after one week of driving I think its gonna be dull again but it looks good anyways good job man
02-08-2005, 04:53 PM
#9
Supreme Member
Thread Starter
Join Date: Dec 2001
Posts: 1,411
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by 1fsstgta
Hey brandon that looks good but after one week of driving I think its gonna be dull again but it looks good anyways good job man
Hey brandon that looks good but after one week of driving I think its gonna be dull again but it looks good anyways good job man
02-08-2005, 06:29 PM
#10
Supreme Member
Join Date: Aug 2002
Location: San Pedro, Ca
Posts: 1,413
Likes: 0
Received 0 Likes
on
0 Posts
Car: White KSwisses
Engine: 5.3L Gen III
Originally posted by james_85Z28
looks good. I have some pushrods you can polish too. Let me knw when I can drop them off.
looks good. I have some pushrods you can polish too. Let me knw when I can drop them off.
You should have him polish the valve springs and roller rockers as well.
02-08-2005, 06:48 PM
#11
Senior Member
Join Date: Aug 2002
Location: So Cal
Posts: 959
Likes: 0
Received 0 Likes
on
0 Posts
would it not be easier to just install the driveline, kick the rear wheels off of the grounds and drop that tranny into gear. Thatll spin the drive line up and all you would have to do is hold a polishing rag to it. i believe i see a yellow one in the pic.
02-09-2005, 09:11 AM
#12
Member
Join Date: Jun 2003
Posts: 361
Likes: 0
Received 0 Likes
on
0 Posts
Brandon, word of advise to you ... to keep it looking great and easy to clean, have it coated with a clear coat, either powder coated or painted on. Looks nice, I wouldn't do it, but it does look nice. 
02-09-2005, 06:56 PM
#13
Supreme Member
Thread Starter
Join Date: Dec 2001
Posts: 1,411
Likes: 0
Received 0 Likes
on
0 Posts
I basically did it to brighten Mikes day.. Letting him know.. Im taking care of the parts I bought from him.. As they are some very nice item's.. To do this polishing, it did not take long.. So if you want to keep your stuff clean.. What's the big deal you know..
This will need maintance just as rims of course.. However it is a good thought to take off the drive line and check the pinion bolt.. This is something that should be checked before you Race etc..
The clearcoat could work out.. Good Idea Gpl.. However I still need to clean this up a lil more..
The rag on the driveline with the wheels turning is an idea.. But however the Saftey Concern..
This will need maintance just as rims of course.. However it is a good thought to take off the drive line and check the pinion bolt.. This is something that should be checked before you Race etc..
The clearcoat could work out.. Good Idea Gpl.. However I still need to clean this up a lil more..
The rag on the driveline with the wheels turning is an idea.. But however the Saftey Concern..
Thread
Thread Starter
Forum
Replies
Last Post
IROCNParts
Engine/Drivetrain/Suspension Parts for Sale
1
09-24-2015 10:50 AM