Quite Roller lifters OEM
#1
Member
Thread Starter
Join Date: Dec 2010
Location: Cal city
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Vett, 2001 Expedition
Engine: 383SBC 435 H/P, 500 TQ
Transmission: 700R4
Axle/Gears: 307
Quite Roller lifters OEM
My 383 up and running BUT I have lifter ticking noise I tryed to adjust them but can get rid of the noise.
I purchased the lifter used they are stock OEM GM everytime I think I saving my self a couple Bucks it turn around and bits me in the rear.
What I have read the 1st Gen OEM GM lifter are know to tick.
The motor will never rev past 5500 RPM's so I dont need a high end high dollar lifter set up.
I running a LT4 Hot cam, Comp Cam Ultra steel 1.6 RRA stock size Harden push rods with guild plates, I dont want to change anything just new QUITE lifters.
But which Brand and what part # I looked at 2nd Gen GM Lifter But I seeing 2 diffrent part numbers which one will work and quite.
I read stay away from Comp Com R lifters hard to get adjusted in.
Anyone what brand and part Number that will not break the bank.
I purchased the lifter used they are stock OEM GM everytime I think I saving my self a couple Bucks it turn around and bits me in the rear.
What I have read the 1st Gen OEM GM lifter are know to tick.
The motor will never rev past 5500 RPM's so I dont need a high end high dollar lifter set up.
I running a LT4 Hot cam, Comp Cam Ultra steel 1.6 RRA stock size Harden push rods with guild plates, I dont want to change anything just new QUITE lifters.
But which Brand and what part # I looked at 2nd Gen GM Lifter But I seeing 2 diffrent part numbers which one will work and quite.
I read stay away from Comp Com R lifters hard to get adjusted in.
Anyone what brand and part Number that will not break the bank.
#2
Member
Thread Starter
Join Date: Dec 2010
Location: Cal city
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Vett, 2001 Expedition
Engine: 383SBC 435 H/P, 500 TQ
Transmission: 700R4
Axle/Gears: 307
Re: Quite Roller lifters OEM
I end up ordering a set of Generation 2 GM lifters from Jegs $121.00.
#3
Supreme Member
iTrader: (8)
Join Date: Oct 2001
Location: Il
Posts: 11,726
Received 773 Likes
on
520 Posts
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: Quite Roller lifters OEM
The ticking is prolly the roller rockers, not the lifters..
#4
Member
Thread Starter
Join Date: Dec 2010
Location: Cal city
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Vett, 2001 Expedition
Engine: 383SBC 435 H/P, 500 TQ
Transmission: 700R4
Axle/Gears: 307
#5
Supreme Member
iTrader: (8)
Join Date: Oct 2001
Location: Il
Posts: 11,726
Received 773 Likes
on
520 Posts
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: Quite Roller lifters OEM
Ok.. good luck with the swap!!! Let us know how it goes
#6
Member
Join Date: Oct 2003
Location: Northern NV
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Trans Am
Engine: 350 TPI
Transmission: T56
Axle/Gears: 3.27
Re: Quite Roller lifters OEM
How does it sound. If its nice and quite I will be following in your footsteps.
#7
Member
Thread Starter
Join Date: Dec 2010
Location: Cal city
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Vett, 2001 Expedition
Engine: 383SBC 435 H/P, 500 TQ
Transmission: 700R4
Axle/Gears: 307
Re: Quite Roller lifters OEM
Fired it up today thats the way it should run.
The new lifters did the trick.
The new lifters did the trick.
Thread
Thread Starter
Forum
Replies
Last Post
91TTOPZ
Exterior Parts for Sale
5
09-20-2016 12:42 PM
skinny z
Engine/Drivetrain/Suspension Parts for Sale
5
10-05-2015 06:23 PM