1987 IROC Project/Roller
Thread Starter
Member
iTrader: (4)
Joined: Jan 2008
Posts: 202
Likes: 0
From: NW Indiana
Car: 1991 Camaro
Engine: Morris 434 Single Turbo
Transmission: TH350
Axle/Gears: 9" Ford w/4.11's
1987 IROC Project/Roller
1987 IROC
No motor/trans
no trans crossmember but I can get you a stock 700R cross for free
Very tiny surface rust by front wheel wells, just light surface, nothing some 100 grit and elbow grease wont take car of...
I have the seats which are descent but I would have them redone and drv seats wont lock in upright position
Has fully reupholstered headliner and sails
2 small cracks in dash
interior needs a good cleaning but is descent
no fog lights
rims are in bad shape and 1 is bent, but tires are pretty new 245/50/16's
gas tank has hole drilled in bottom and -6 fitting installed (cheapo sump?)
stock harness has been modified for a carb'd SBC
Now the good stuff:
G92 car
Jegster torque arm installed (carpet has been cut but fixable
Custom shifter installed (took 6-8 hours to fab in the console and looks sweet)
still has all gauges and 305 TPI ECM in the car
everything works
pillar gauges for water and oil
The underside of the car is very clean. Slight midwest surface rust but ABSOLUTELY NO ROT!!!
I was going to make this a track beast but I have decided to go with my other hard-top car instead.
There are a total of 45+ pics of the car and then a few of the seats.
It's not perfect, but this car is in good shape, do what you want with it??
Asking $1,100 or trade for a 9" or 12 bolt rearend ready to go.
More pics available upon request
http://s125.photobucket.com/albums/p...212/87%20IROC/
No motor/trans
no trans crossmember but I can get you a stock 700R cross for free
Very tiny surface rust by front wheel wells, just light surface, nothing some 100 grit and elbow grease wont take car of...
I have the seats which are descent but I would have them redone and drv seats wont lock in upright position
Has fully reupholstered headliner and sails
2 small cracks in dash
interior needs a good cleaning but is descent
no fog lights
rims are in bad shape and 1 is bent, but tires are pretty new 245/50/16's
gas tank has hole drilled in bottom and -6 fitting installed (cheapo sump?)
stock harness has been modified for a carb'd SBC
Now the good stuff:
G92 car
Jegster torque arm installed (carpet has been cut but fixable
Custom shifter installed (took 6-8 hours to fab in the console and looks sweet)
still has all gauges and 305 TPI ECM in the car
everything works
pillar gauges for water and oil
The underside of the car is very clean. Slight midwest surface rust but ABSOLUTELY NO ROT!!!
I was going to make this a track beast but I have decided to go with my other hard-top car instead.
There are a total of 45+ pics of the car and then a few of the seats.
It's not perfect, but this car is in good shape, do what you want with it??
Asking $1,100 or trade for a 9" or 12 bolt rearend ready to go.
More pics available upon request
http://s125.photobucket.com/albums/p...212/87%20IROC/
Thread Starter
Member
iTrader: (4)
Joined: Jan 2008
Posts: 202
Likes: 0
From: NW Indiana
Car: 1991 Camaro
Engine: Morris 434 Single Turbo
Transmission: TH350
Axle/Gears: 9" Ford w/4.11's
Re: 1987 IROC Project/Roller
Still available...... taking interesting trade offers as well.
Thread
Thread Starter
Forum
Replies
Last Post
TA8487
Interior Parts Wanted
3
Aug 23, 2015 01:34 PM




