Unfortunately, due to hard times I am unable to continue on with my IROC project. I had lots of plans for it, but I am in no financial situation to complete what I have started.

Car:
1988 IROC-Z Convertible
Originally a canadian car
HAD a 305TBI and T5 Transmission


The IROC's interior consists of a 4th gen dash with functioning gauges, 4th gen center console, 4th gen seats, nice carpet 97 Delco radio with working CD player, rear pioneer speakers, and I may just throw in the 2 12" Punch subs and 800w MTX Amplifier that are in the trunk.

Performance/suspension mods that are already done to the car include:
87 BW 9-bolt Posi (3.23) rearend with new gear oil, new rotors, new pads, and new calipers painted red. It has Lakewood lower control arms, and a Lakewood adjustable panhard bar. Newer KYB GR2 Shocks/struts all the way around, and AG Lowering springs installed as well. Energy Suspension endlinks on both swaybars which are the Largest you can get (36mm/24mm). The Front Brake calipers and pads have also been replaced with very little miles on them. The hood is a Harwood 3" bolt on show series hood, made of fiberglass and is realllllly light! Also has Flowmaster muffler and the piping all the way up to the Y (complete). The car needs Paint and body work, and a new Top.


5.7l (350ci) LT1 Complete with Aluminum heads and ALL accessories
T56 6 speed transmission, fork, clutch, and bellhousing, shifter..
Edelbrock Emissions legal headers and Y-pipe
Prepped 3rd gen under-hood harness
Full LT1 Engine harness with ECM
Master/Slave cylinder with steel braided line
LT1 Radiator with all hoses
LT1 Dual fan setup
LT1 Throttle cable

Extra parts that are included:
Extra set of good doors
2 sets of convertible spoilers (Need work)
Extra convertible tonneau lid
Anything else I can find (I have lots of parts)

The only other parts needed to complete the LT1 swap are a $51 Fuel pump, and a $105 T56 Transmission crossmember, or have one made.

I will most likely be installing the engine and LT1 swap parts in the coming days unless there is interest before hand. The front tires have about 80% tread left, and the rears have about 50% left.



Fiero spoiler has been removed, but the buyer can have it if they want it, lol.




These pics are probably a month or two old, I will have new pics tomorrow, the car is in the same shape, just no motor currently installed.

I would like to get $3000 out of the entire package. If I make enough money to buy the crossmember and fuel pump, I will install those as well.

Located in Tampa, florida.

Thanks

 

 

SOLD! till i seen it was in florida darn

 

Wish you were in Florida.

More pics and info in this thread:
https://www.thirdgen.org/forums/conv...nvertible.html

Engine is going into the car on sunday, and pics will be taken.

 

Engine is in.

I will include any of my extra third gen parts that I have to the buyer, this is ALOT of parts, bring a truck.





Other LT1 parts (and a single fan if wanted):


Heres the headers, Y, and driveshaft.


Thanks.

 

wow one hell of a deal. Do you have car wired and running or is it just bolted in?

Wish you was closer I would buy right now...

I just sold my 91 Vert in my sig ROLLING for $4000 on ebay

 

Just bolted in, but I prepped the third gen c100 allready, and have the full 94 LT1 Engine harness included as well. I don't have the money to get it running just yet. I have never sold a car on eBay before, but it is my last resort. I will consider trades, but I am picky.

 

I sure wish I had the money.

 

Me too.

 

Bump.

 

Bump.

MUST SEE!

 

Been working on the wiring.

Will hopefully be done with the wiring in a few days or so.

BUMP!

This is a deal, MUST SEE!

 

In all seriousness, if you get the wiring finished... I might add on another student loan to get this beast.

 

I am making good progress on the wiring. I see no reason it shouldnt be all wired up in 1-2 days max.

 

Got pretty much all of the under-hood wiring hooked up, and put in the battery, all of the lights came on as they should, etc.. I couldnt fully test it yet though, as the car still needs a bigger fuel pump, crossmember, and a pulley. I will be ordering these parts in a few days most likely. If I get it running/driving, I will want more money.

 

Bump

I am contemplating putting more money in it, I am broke enough. LOL

$3000 is a STEAL! Doesnt need much more to be running!

 

Update:

I am buying/ordering the parts necessary to get this beast up and running.

When I get it running and driving I will post a new ad, so it isnt so cluttered.

Stay tuned.

 

What will you be asking for once it's finished? My brother is interested and has $$$ in hand

 

$3500.

Ive bought more in JUST parts since then.

Check out the build thread for more info on the car:
https://www.thirdgen.org/forums/conv...nvertible.html

 

Man you've really put a lot into it all! Why you selling so cheap?

 

I need something I can drive, so I can get a job. lol