When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
***$1,250/TRADE***RUST FREE Camaro Berlinetta Virginia car (located in WNY/Buffalo)
***NO TITLE***
***$1,500 FIRM***
(Trades considered, can deliver... please read full add before contacting me, thanks)***
Hello, for sale is a rust free Virginia car i recently acquired from a good friend who's grandfather just passed away... I was told the car is a 86 but after looking at it I believe it to be a 1987... however I was told that 86 was the last year for the Berlinetta
First and foremost, this car has NO TITLE.. it was lost years ago... however I can see what I can do about getting a replacement but I doubt it's going to happen.. I myself would rather pull my eyelids off than deal with lost title recovery at the DMV..
Interior is beautiful other than the saggy headliner... no tears or rips in the seats, carpet is nice.. door panels good... the dash pad AND center console lid are both crack free and original.
No leaks of any kind, steering wheel wrap is in great shape... good glass and so on.
Paint and clear coat are original and it clearly shows, body is in great condition with the only dent worth mentioning being directly behind the LR wheel on the quarter panel(looks as though its been pushed in just a bit) the rest of the body is in great condition... 2 other small imperfections is a crack in the grille and the very far right hand forward corner of the hood is not aligned perfectly with the front bumper cover (fender to hood lines and all other body lines for that matter are fine)
Under the hood is a clean original V6 with an auto OD transmission. I am unsure of the gear ratio but the console lid is original so I can look into the R.P.O. codes...
Car runs and drives but the engine has a faint knock... this car would be perfect for a drag car build or track day/auto-x car...
On another note I have piles and piles of parts for third gens, 4th gens, G-Bodys and SBC/LSX in general... from body and interior[Almost ALL camaro not much for pontiac](rust free fenders, doors/light rust fenders & doors/NOS fenders, standard steel hoods, IROC hoods w/louvers, ground effects, bumper covers, 1 white WS6 Trans-Am 98-02 rear bumper cover, T-Tops) too complete rear ends(factory 4th & 3rd gen and a killer H.D. Strange Engineering 12 Bolt), posi units(Eaton, Auburn, G80 and Torsion), gear sets(3.23's, 3.42's, 3.73's and 4.11's new and used....Perfect Launch aluminum girdle with lash caps, ARP Carrier Bearing Studs), brakes(Front and rear calipers/rotors/pads & hardware from 98-02 F-Body and rear PBR from 93-97), suspension components(srandard front/rear springs as well as WS6/IROC springs, 36/34mm front bars, 19/21mm rear bars, Moog & EnergySuspension end links, factory front A-arms and LCA's [82-92 & 93-02]), bushings and steering parts(SPOHN full steering kit & ball joints, poly LCA bushings poly front A-arm bushings[4th gen] spindles & hubs[4th gen]), gauges, wheels & tires(14" Oldsmobile wheels and NEW 18x9.5"/18x10.5" C5 Replicas with NEW 275-35&295-35 Continental EXTREME Contact DW's), fuel system parts, radiators, electric fans, fan controllers, NASCAR toggle switches, waring/indicator lights, Autometer gauges, custom built camaro gauge cluster, some LSX swap components and performance parts(UMI LSX K-Member, Spohn SFC's, mabey some headers, cat back exhaust system's), good complete engines and transmissions (a couple 350 4 bolt mains 010 high nickel blocks, LS1, LS6, LS2 and a aluminum what I call "H.O." 5.3L [originally 335hp out of a 07 trailblazer] short blocks...TH350's, LS1<1 T56's[as well as a couple t56 swap parts]...OTHER SBC parts and alot of LSX parts, Carbs, Intakes(gen3/4 LS6 modified by T.P.I.S., Vic Jr for LS3, GM truck intakes, 2 TBSS[Trailblazer SS] intakes, gen1 performer, performer RPM, performer RPM air gap, Holley dual plane), heads(not much for gen1 other than smog and a set of "H.O." 305 swirl ports, gen3/4 243,841,853,799 & 823), front drive components(gen1 & gen3/4 Fbody & Truck alts/PS/water pumps/AC/starters & balancers), camshafts (gen1 Crane hyd flat, 3 different gen3/4 CompCams hyd rollers) valve springs, LS7/GM hyd replacment lifters, OE pushrods, rocker arms, timing sets, lifter trays, windage trays, oil pans, ALL HARDWARE FOR 98-02 FBODY AND GEN3/4 LS ENGINES) under hood dress up and OE engine covers(Edelbrock std hieght and MOROSO racing tall valve covers [both gen1 pre-86] different style covers for gen3/4..valve/valey/front & rear), goodies from our Ashpalt Modified Race car team like aluminum Tilton Bellhousings, Tilton Remote masters, remote reservoirs, Wilwood calipers and even some NASCAR parts... you name it I got it or can get it) WAYYY TO MUCH TO LIST... if you are interested in the car please give me a call or preferably send me a text message... I have a constantly changing sleeping schedule so text me your name and what your inquiring about and I will get back to you as soon as I can.... you can also send me a PM on here but to be honest I rarely come on this site anymore other than to browse the classified adds ...
Thank you for your interest,
Adam.
(716)428-1674
****Located in Buffalo NY-14228
I can ship all items including engines/transmissions/rear ends and I can deliver cars but I will not sell a vehicle without the buyer physically seeing the car in person****
Saggy headliner Good seats, carpet and door panels... Good leather wrap on wheel and shifter, good plastics(shifter plate, radio surround, A/C dash, upper and lower center console) & crack free dash pad & console lid. GM OEM N.O.S. Camaro fenders and radiator support/header Can see the crack in the grille I mentioned here Can see the far right front corner of the hood I mentioned here Needs a good bath!!!
We also build engines and cars, here is my personal ls3 headed carbed Iron 408 yet to be finished ... (also could be for sale for the right stack of cash!)
10-21-2017, 05:13 AM
